Unpacking the Unit, Framing | Hearth and Home Technologies SFE-35

A Unpacking the Unit

WARNING! Do NOT use this appliance if any part has been under water. Immediately call a qualiﬁed service technician to inspect and to replace any part of the electri- cal system if necessary.

Carefully remove packaging from the unit. The front screen is held in place with four Phillips head screws. To remove the screen, extract the screws. Grasp the screen frame and pull out.

B. Locating Your Electric Fireplace

Your new electric ﬁreplace may be installed virtually anywhere in your home. However, when choosing a location ensure that the general instructions are followed. For best results, install out of direct sunlight.

Power supply service must be either completed or placed within the heater prior to ﬁnishing to avoid reconstruction.

Protective cover may stay on during framing, but must be removed before ﬁnal ﬁnishing. Once ﬁnal ﬁnishing has been completed, the protective cover can be used to protect the heater until ﬁnal installation is complete.

F. Hardwire Electrical Connections

WARNING! Electrical wiring must comply with local building codes and other applicable regulations to reduce the risk of ﬁre, electrical shock and injury.

Note: All wiring must be completed prior to ﬁnishing the unit.

For supply connections use No. 14 AWG or larger wires. Use copper wire only. Connect only to a 15 AMP branch circuit. A dedicated circuit is recommended as other appliances on the circuit may cause the breaker to trip or fuse to blow when the heater is operating.

•Remove the screws securing the junction block cover.

•Wire to a properly grounded, 120 volt, 60 Hz, 15 AMP circuit

•Ensure all junction block connections are tight.

•Replace the cover and retaining screws.

•Plug in the IEC-320-C14 power plug to the IEC-320-C13 power inlet located on the upper right side of the unit.

•All components and wiring may be inspected by removing the top inter-panel through the ﬁreplace front opening.

C. Clearance to Combustibles

Sides . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 in. (0 mm) Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 in. (0 mm) Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 in. (0 mm) Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 in. (0 mm)

D. Framing

•Choose a fireplace location and frame as shown in Figure 2.1.

•Frame in the ﬁreplace with a header across the top.

•It is important to allow for ﬁnished face when setting the depth of the frame.

•If a hearth system or raised hearth is to be installed, the unit MUST be raised to provide service access and use of optional fronts.

•The ﬁreplace can now be positioned in the opening.

•Level it with shims if necessary, and attach the unit to the frame using the nailing ﬂanges provided.

E. Electrical Speciﬁcations

Voltage . . . . . . . . . . . . . . . . . . . . . . 120 V AC, 60 Hz

Total Amps . . . . . . . . . . . . . . . . . . . . . . . . . .9.6 AMP

Total Watts . . . . . . . . . . . . . . . . . . . . . . . 1050 Watts

Heater Rating . . . . . . . . . . . . .1000 Watts/3415 BTU

G. Wall Switch and Thermostat Connections

WARNING! Do NOT connect the optional low voltage switch and/or thermostat to 120 volt branch circuit.

The Optional Wall Switch 4050-309 contains two single pole switches. (LEVITON 5634 Series or equal)

The Optional Wall Thermostat is a low voltage mechanical type. (Columbus Electric RK120EAA or equal)

Maximum run distance is 30 ft. (9.14 m) with 20 gauge solid copper low voltage thermostat wire. Connect per the electrical wiring diagram on page 7.

H. Finishing

Combustible or non-combustible materials may be used to ﬁnish up to the ﬁreplace opening.

Note: ensure that you leave adequate room to remove and replace the front screen or optional front.

4	Hearth & Home Technologies Inc. • SFE-35 • 4050-313 Rev C • 01/08

SFE-35 specifications

Hearth and Home Technologies (HHT) is a recognized leader in the development and manufacture of innovative hearth products. Among their offerings, the SFE-35 and SFE-35C are standout models, providing exceptional heating solutions for modern homes. These two insert models exemplify the embodiment of quality craftsmanship, efficiency, and user-friendly features, making them popular choices for homeowners seeking style and functionality.

The SFE-35 is designed with an emphasis on versatility and efficiency. It boasts a sleek design that seamlessly blends with various home decors, ensuring that it complements both contemporary and traditional settings. One of its key features is the powerful heating capacity, generating an impressive output while maintaining a high level of energy efficiency. The model is equipped with advanced secondary combustion technology, which promotes cleaner burning and helps minimize emissions while maximizing heat output.

The SFE-35C variant extends its usability with added convenience and functionality. It comes with an easy-to-operate electronic ignition system, allowing users to start the fireplace with a simple push of a button. Additionally, the SFE-35C is known for its smart control features, which can integrate with home automation systems for enhanced user experience. With the ability to adjust settings through mobile apps or remote control, homeowners can manage their heating with precision and ease.

Both models come with a range of customizable options, including various fronts and finishes to match individual style preferences. The large viewing window offers a radiant display of flames, creating a cozy atmosphere in any living space. Moreover, the units are constructed with durable materials, designed to withstand the test of time while providing reliable performance.

Safety is another hallmark of the SFE-35 and SFE-35C models. They include built-in safety features such as thermal overload protection and advanced venting systems to ensure proper air circulation and prevent any potential hazards.

Overall, Hearth and Home Technologies' SFE-35 and SFE-35C models represent a fusion of art and science, bringing warmth and comfort to homes. With their cutting-edge technology, efficient heating capabilities, and elegant design, they are ideal choices for those looking to enhance their living space with a modern fireplace solution.