Hearth and Home Technologies FL92 Installation of Fireplace, Things to Consider, Level Fireplace

Page 21

7 Installation of Fireplace

CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

A. Things to Consider

Location of chimney air kit inltet (see Figure 5.1 & 7.4)

Location of outside air kit

Electrical connections and/or wall switch

Gas line piping

B. Position the Fireplace

Place the fireplace on a continuous flat surface.

Follow framing instructions in Section 6.

WARNING! Risk of Fire! Prevent contact with sag- ging, loose insulation.

DO NOT install against vapor barriers or exposed insulation.

Secure insulation and vapor barriers.

Provide minimum air space clearances at the sides and back of the fireplace assembly as outlined in Section 6.

C. Place Protective Metal Hearth Strips

WARNING! Risk of Fire! Protective metal hearth strips MUST be installed. DO NOT cover metal strips with com- bustible materials. Sparks or embers may ignite flooring.

Refer to Figures 7.1 and 7.2.

Locate the two protective metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm) included with this fireplace.

Slide each metal strip 2 in. (51 mm) under front edge of fireplace.

Overlap strips in the middle of fireplace opening by 1 in. (25 mm) minimum..

Metal strips must extend beyond the front and sides of the fireplace opening by at least 2 in. (51 mm).

Protect the front of a platform elevated above the hearth extension with metal strips (not included with fireplace) per Figure 7.2. See Section 11 for hearth extension instructions.

D. Level Fireplace

Level fireplace side-to-side and front-to-back.

Shim with non-combustible material as necessary.

Secure fireplace to framing with nailing flanges with a minimum of two fasteners per nailing flange.

Check fireplace opening for square to ensure proper fit of glass doors. Measure diagonals of fireplace opening to make sure they are equal.

1 in. (25 mm) overlap

Metal strips 2 in. (51 mm) under the edges of the fireplace and must extend beyond the front and side openings by 2 in. (51 mm)

Figure 7.1 Position the Protective Metal Hearth Strips

 

Top piece must overlap

 

bottom piece

 

Raised Platform

2 in.

1 in. (25 mm) min.

(51 mm)

overlap

Floor

2 in. (51 mm)

Figure 7.2 Protect the Front of an Elevated Platform

Heatilator • Multi-Sided Woodburning Fireplace • 34955 • Rev V • 11/08

21

Image 21
Contents Hot screen/mesh and glass doors will cause burns Fire RiskListing Label Information/Location GrateNumber Model Table of Contents Installer GuideUser Guide Limited Warranty Hearth & Home Technologies Limited Warranty 4021-645A Appliance Certification Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Starting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceWood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for RemovalCheck Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet AK14/AK18 Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldInstall Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in RoofFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shieldRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredFinishing Hearth Extension= 1/k x inches of thickness Hearth Extension Dimensions In. Micore or equivilent insulation Finishing MaterialFlush Front Combustible MantelGas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference Materials13 mm Catalog # Chimney Components15-1/4 387 mm 15-3/4 400 mm FL92 Service PartsContact Information

FL92 specifications

Hearth and Home Technologies (HHT) has long been recognized as a leader in the hearth industry, providing innovative and efficient heating solutions. Among its impressive lineup, the FL92 stands out as a versatile and modern gas fireplace that enhances both ambiance and functionality in various living spaces.

One of the main features of the FL92 is its expansive viewing area. The large glass front offers an unobstructed view of the flames, creating a mesmerizing focal point for any room. It allows consumers to enjoy the warmth and beauty of a traditional fire without the hassle of wood or ash cleanup. The design effectively blends contemporary aesthetics with practicality, making it an appealing choice for modern homes.

In terms of technology, the FL92 is equipped with advanced heating capabilities. It utilizes a powerful yet efficient burner system that provides reliable heat output while maximizing fuel efficiency. This means homeowners can enjoy a cozy atmosphere on chilly evenings while being mindful of energy consumption, potentially leading to lower utility bills.

Additionally, the FL92 features a variety of customizable options to suit individual preferences and home décor. Customers can choose from different finishes, media options, and decorative fronts to create a personalized look that complements their interior design. This level of customization ensures that the FL92 can be seamlessly integrated into any space, whether it’s a contemporary loft or a traditional living room.

Another standout characteristic of the FL92 is its easy installation and user-friendly operation. HHT has designed the unit with the homeowner in mind, making it compatible with a variety of installation scenarios, including zero-clearance applications. This versatility simplifies the process for contractors and homeowners alike.

Safety is also a top priority for HHT, and the FL92 is designed with several safety features, including an automatic shut-off function and a tempered glass front that remains cool to the touch. These elements not only provide peace of mind but also contribute to the overall user-friendly experience.

In conclusion, the Hearth and Home Technologies FL92 is a modern gas fireplace that combines aesthetic appeal with advanced heating technology and safety features. Its spacious viewing area, customizable options, and efficient operation make it an excellent choice for those looking to enhance their living spaces with the warmth and ambiance of a sophisticated fireplace. Whether for new builds or renovation projects, the FL92 stands out as a reliable and stylish option in the world of home heating solutions.