Hearth and Home Technologies RUTHERFORD-50 Install Side Molded Brick Panel-Herring- bone

Page 36

D. Install Side Molded Brick Panel-Herring- bone

•If a gas line is to be installed, remove the knockouts in the inner firebox and in the outer shell on the side of your choice. Refer to dimension drawings for location of knockouts and Section 13.A. for gas provisions.

•Do NOT remove screen rods.

•Refer to Figure 11.2.

•Install lower side panel, tapered edge to the front. Align the front edge with the front of the column (or butted to the surround if installed).

•Install two T-brackets stem down into mortar line, do not tighten.

•Install upper side panel in the unit, tapered edge to the front. Position the bottom of panel behind the T-brackets. Install two T-brackets stem up into mortar lines, one Y- bracket on the front edge as shown. Do not tighten.

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

•Install second side panel following the steps above.

Note: Use T-brackets as templates and drill pilot holes into the inner shell with the drill bit provided. Side panels must be installed first.

E. Install Back Molded Brick Panel-Herring- bone

•Refer to Figure 11.2.

•Set the grate brackets in place, 26.5 in. (673 mm) center to center.

•Install the lower back panel. Center from side to side.

•Install two T-brackets stem down into mortar line to hold lower back in position. Do not tighten.

•Install upper back panel. Position bottom of panel behind the previously installed T-brackets. Install three T-brackets stem side up into mortar line, do not tighten

•Install two Z-brackets in the mortar joints across the top. Tighten these and all previously installed brackets.

 

Front

 

 

Upper Side

Upper Back

 

Molded Brick Panel

Molded Brick Panel

 

 

Lower Back

 

 

Molded Brick Panel

 

Lower Side

 

 

Molded Brick Panel

 

 

 

Grate Brackets

 

 

Hearth Molded Brick Panel

Figure 11.2 Herringbone Molded Brick Panel

 

36

Heat & Glo • RUTHERFORD-50 • 4059-333 Rev F • 11/08

Page 35 Page 37
Image 36
Page 35 Page 37
Contents RUTHERFORD-50 Homeowner Reference Information Listing Label Information/LocationTable of Contents Installer GuideUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo RUTHERFORD-50 4059-333 Rev F 11/08 Listing and Code Approvals Appliance CertificationNon-Combustible Materials Combustible MaterialsOperating Instructions Your FireplaceSeasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Hardwood vs SoftwoodMaintainance and Service Chimney Inspection/CleaningDisposal of Ashes Glass Cleaning Check Firebox Molded Brick PanelInspect Grate Troubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDesign and Installation Considerations DraftNegative Pressure Locating your Fireplace & Chimney Recommended Chimney LocationsTools and Supplies Needed Typical Fireplace ComponentsInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplaceInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsInstall Outside Air Kit Outside Air Inlet LocationsChimney Assembly Chimney Requirements Height of Chimney ComponentsInstallation Notes Install FirestopFrame Openings Cut Roof OpeningAssemble Chimney Sections Supplementary Support and StabilizerInstall Attic Insulation Shield Install Roof Radiation ShieldsOffset Elbow Installation Finish TopEnclosures Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase Top FlashingInstall Termination Cap Shrouds Shroud RequirementsHouse Style Shroud Minimum Dimensions House Style ShroudArch / Mailbox Style Shroud Pyramid Style ShroudInstallation of Molded Brick Panel Install Hearth Molded Brick PanelInstall Side Molded Brick Panel-Traditional Install Back Molded Brick Panel-TraditionalInstall Side Molded Brick Panel-Herring- bone Install Back Molded Brick Panel-Herring- boneInstall Mortar Install ScreensFinishing Hearth Extension= 1/k x inches of thickness Raised Hearth Extension Framing Non-combustible Sealant Finishing Material Noncombustible FacingCombustible Mantel Mantel, Adding Extra Support 12 Notch the Metal TrackBrick Front Accessories Gas Log/Lighter ProvisionWood Burning Inserts Fireplace Dimensions Reference MaterialsChimney Components Catalog # DescriptionParts RUTHERFORD-50This page intentionally left blank This page intentionally left blank This page intentionally left blank Do not Discard this Manual

RUTHERFORD-50 specifications

Hearth and Home Technologies (HHT) has long been recognized for its innovative approach to home heating solutions, and the Rutherford-50 is a shining example of their commitment to quality and performance. This versatile fireplace is designed to not only provide warmth but also enhance the aesthetic appeal of any living space.

The Rutherford-50 is a gas-fired fireplace that effortlessly combines modern technology with traditional design. One of its standout features is the large viewing area, which allows for an unobstructed view of the flames, creating an inviting focal point in any room. With its clean lines and elegant design, it complements various interior styles, from contemporary to rustic.

A major advantage of the Rutherford-50 is its advanced ignition system. Utilizing electronic ignition technology, it ensures reliable and quick starts, enhancing user convenience, especially during cold weather. The fireplace also includes a user-friendly remote control, allowing homeowners to adjust heat output and flame settings with ease.

Efficiency is a key characteristic of the Rutherford-50. The fireplace boasts an impressive thermal efficiency rating, ensuring that it effectively heats the room while minimizing energy consumption. This not only helps in reducing utility bills but also contributes to a more environmentally friendly home heating solution.

The Rutherford-50 also emphasizes safety and functionality. It features a built-in safety pilot, which automatically shuts off the gas flow if the flame goes out, providing peace of mind for families. Additionally, the fireplace is equipped with a barrier screen to prevent accidental contact with the flames, making it suitable for homes with children and pets.

Customization options are another attractive aspect of the Rutherford-50. Homeowners can choose from various decorative features, including different media options like logs, rocks, or glass, allowing them to personalize their fireplace to fit their unique style.

In summary, the Hearth and Home Technologies Rutherford-50 is a sophisticated gas fireplace that marries style and functionality. With its large viewing area, advanced ignition system, impressive efficiency, and customizable options, it represents a remarkable choice for anyone looking to enhance their home heating experience. Whether for warmth or ambiance, the Rutherford-50 provides an unparalleled solution that aligns with modern living.
Top Page Image Contents