Hearth and Home Technologies ST-TRC manual Installing Vent Components, Venting Out the Rear Vent

Page 27

B. Installing Vent Components

After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly.

Venting Out the Rear Vent

Remove the installed rear seal cap from the rear starting collars by removing screws (see Figure 17). Follow the vent configuration tables accordingly.

Remove the insulation from the REAR five inch flue, pull the heat shield out from outside of the firebox.

WARNING: THE TOP HEAT SHIELD (INSIDE

!THE FIREBOX) MUST REMAIN ATTACHED IF THE VENT SYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE 17.

Venting Out the Top Vent

Remove the screws in the top vent collar seal cap and re- move the top vent collar seal cap and insulation inside the top starting collar (See Figure 17).

Remove the heat shield from inside the TOP five inch flue from outside of the firebox.

The glass must be taken off again for positioning the logs when the unit is finally installed in place and finished around it. Re-install the glass door. Attach vent system to the top starting collars.

WARNING: THE REAR VENT COLLAR SEAL

!CAP MUST REMAIN ATTACHED TO THE REAR VENT COLLARS IF THE VENT SYSTEM IS AT- TACHED TO THE TOP STARTING COLLARS.

WARNING: FAILURE TO REMOVE INSULATION

!IN THE SET OF COLLARS YOU ARE USING COULD CAUSE A FIRE.

!WARNING: YOU MUST LEAVE THE INSULATION IN PLACE IN THE SET OF COLLARS YOU ARE NOT USING.

If your vertical vent component is over 10 feet, you may want to install the vertical baffle (located in the bag containing the install manual) to improve flame appearance. Center the vertical baffle on the 5” flue being used, and with self tapping screws secure the baffle to the inside of the firebox.

1.Attach the First Vent Component to the Starting Collars

To attach the first vent component to the starting collars of the fireplace:

•Apply a 3/8 inch (9.5mm) bead of stove cement around the 5 inch (127mm) fireplace starting collar.

•Make sure that the fireplace rope gasket supplied with the fireplace seals between the first 8-5/8 inch (219mm) vent component and the outer fireplace wrap.

•Lock the vent components into place by sliding the con- centric pipe sections with four (4) equally spaced interior beads into the fireplace collar or previously installed com- ponent end with four (4) equally spaced indented sections.

•When the internal beads of each 8-5/8 inch (219mm) outer pipe line up, rotate the pipe section clockwise about one-quarter (1/4) turn. The vent pipe is now locked together.

STARTING

COLLAR

STOVE

SEALANT

BEAD

FIRST VENT

COMPONENT

1 INCH (25.4mm)

Figure 18. Attaching the First Vent Component to the Starting Collars

Venting Out Rear

SEAL

CAP

HEAT

SHIELD

DISCARD

INSULATION

and

HEAT SHIELD

Figure 17

Venting Out Top

SEAL

 

CAP

 

DISCARD

 

INSULATION

 

and

 

HEAT SHIELD

HEAT

 

SHIELD

!WARNING: A 3/8 INCH (9.5 MM) BEAD OF STOVE CEMENT MUST BE PLACED AROUND

THE 5 INCH (127 MM) FIREPLACE STARTING COL-

LAR BEFORE ATTACHING THE FIRST VENT COM- PONENT. FAILURE TO SEAL THIS JOINT MAY CAUSE THE FIREPLACE TO OPERATE IMPROPERLY. SEE THE DIAGRAM .

!WARNING: ENSURE THAT THE FIBER- GLASS ROPE GASKET SUPPLIED WITH

THE FIREPLACE SEALS BETWEEN THE FIRST VENT COMPONENT AND THE OUTER FIREPLACE WRAP.

If the installation is for a termination cap attached directly to the fireplace, skip to the sections, Install Firestops and Vent Termination.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents Pier-TRC PIER-TRC NG, LP Exploded Parts Diagram / Vue éclatée des piècesST-TRC ST-TRC Corner-TRC CORNER-TRC Corner-TRC Common Parts / Piéces Communes Serial # Part Number Certification Installation CodesHigh Altitude Installations Appliance CertificationPre-install Preparation Introducing the Heat-N-Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the PIER-TRC Diagram of the ST-TRC Diagram of the L & R CORNER-TRC Framing the Fireplace Locating the FireplaceModel 32 156mm 187mm Termination kits Installing the Vent SystemIdentifying Vent Components Vent System ApprovalsMax. Run Straight UP Vertical VentingMAX .4 M Straight Up Vertical Venting Straight OUT Horizontal VentingVenting with ONE 1 90 ElbowVenting with ONE 1 90 Elbow Venting with Two 90 Elbows Venting with TWO 2 90 ElbowsVenting with TWO 2 90o Elbows Venting with Three 3 90 Elbows Venting with Three 3 90 Elbows Attach the First Vent Component to the Starting Collars Installing Vent ComponentsVenting Out the Rear Vent Venting Out the Top VentAdding Venting Components Install Support BracketsCeiling Firestop Ceiling Side Minimum Trapezoid CAP Termination Vent TerminationPositioned SO That the Arrow is Pointing UP 191mmVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Nected to Acontrol Valve in Amillivolt System Positioning, Leveling, and Securing the FireplaceGas Control System Standing Pilot Ignition SystemGas Supply Line Gas Pressure RequirementsNatural Gas Propane Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional AccessoriesOperation using Battery Power For Intermittent Pilot Ignition IPI WiringSealant Material Hearth Extensions FinishingGlass Specifications Installing Trim, Logs & Ember MaterialLighting the Fireplace After the InstallationDouble-check for faulty components Before Lighting the FireplaceReplacing old ember material Fireplace MaintenanceCleaning Glass Door Important Turn OFF the GAS Before Servicing Your Fireplace

L-CORNER-TRC, R-CORNER-TRC, ST-TRC, PIER-TRC specifications

Hearth and Home Technologies offers an impressive range of fireplace products that blend aesthetics with advanced technology. Among their innovative lineup, the PIER-TRC, ST-TRC, R-CORNER-TRC, and L-CORNER-TRC models stand out as versatile and stylish options for modern homes. Each of these fireplace units is designed to enhance the ambiance of a space while providing reliable performance.

The PIER-TRC model is ideal for those seeking a focal point in a living room or gathering space. This pier-style fireplace is characterized by its striking, contemporary design and clean lines. It allows for a three-sided view of the flames, creating a captivating visual experience from various angles. The PIER-TRC incorporates advanced venting technology, ensuring efficient heat distribution without compromising on aesthetics. Homeowners can choose from a selection of decorative media options to personalize the appearance, adding a unique touch to any interior.

Next, the ST-TRC model is a sleek, modern fireplace that excels in providing both form and function. Its space-saving design makes it a perfect choice for smaller rooms while still delivering ample heat output. The ST-TRC features a linear, minimalist look that fits seamlessly with contemporary decor. Advanced electronic ignition systems enable effortless operation, while the option for smart home integration allows users to control the fireplace with ease using mobile devices.

For those looking to create a cozy corner in their living space, both the R-CORNER-TRC and L-CORNER-TRC models offer an excellent solution. Designed specifically for corner placements, these fireplaces feature a unique design that allows for a two-sided viewing experience. The R-CORNER-TRC wraps around the right side, while the L-CORNER-TRC offers a similar aesthetic for the left. Both models utilize cutting-edge technology to ensure efficient heating and combustion, with adjustable flame settings that let users customize their experience.

All of these models come equipped with high-efficiency burners, maximizing heat output while minimizing fuel consumption. Hearth and Home Technologies ensure that each unit meets stringent safety and performance standards. With a commitment to quality and innovation, they provide homeowners with stylish and functional solutions that enhance the warmth and comfort of their living spaces.

In conclusion, the PIER-TRC, ST-TRC, R-CORNER-TRC, and L-CORNER-TRC fireplaces from Hearth and Home Technologies provide a perfect balance of elegance, efficiency, and versatility. Each model showcases advanced technologies and design features that cater to modern needs, making them an excellent choice for any home.
Top Page Image Contents