Hearth and Home Technologies ST36D owner manual Install Attic Insulation Shield

Page 29

F. Install Attic Insulation Shield

WARNING! Risk of Fire! You MUST install an attic insu- lation shield when there is any possibility of insulation or other combustible material coming into contact with the chimney.

•DO NOT pack insulation between the chimney and the attic insulation shield.

•Failure to keep insulation and other materials away from chimney pipe could cause fire.

•DO NOT offset chimney inside insulation shield.

Installation of a ceiling firestop is required

•Refer to Figures 8.6 - 8.8.

•Roll the shield (around the chimney if already installed) until you have a 3 in. (76 mm) overlap and the three holes on each side match up (large holes on top).

•Insert three screws into the matching holes to form a tube.

•Bend three tabs on the bottom of the tube inward to 90° to maintain chimney air space (refer to Figure 8.6).

•Rest the insulation shield on the ceiling firestop below.

•Bend the three short tabs at the top of the shield inward to 90° to maintain the 2 in. (51 mm) air space from the chimney.

•Bend the remaining top tabs to just meet the pipe.

If you wish to make a custom shield or barrier, follow these guidelines:

•Metal is preferred, although any material stiff enough to hold back the insulation can be used.

WARNING! Risk of Fire! Use of cardboard or other materials that can deflect under humidity or other envi- ronmental conditions is not recommended.

•The shield or barrier must be tall enough to extend above the insulation and prevent blown-in insulation from spilling into the cavity.

•Maintain specified air spaces around chimney.

•Check instructions and local codes for further details.

 

 

 

 

Bend remaining tabs

 

 

 

 

to rest against pipe to

Bend

 

inward

prevent insulation

90°

 

from falling in.

 

 

 

 

 

Insert three

 

 

 

 

screws

3 in. (76 mm) overlap

Figure 8.6 Prepare Attic Insulation Shield

 

 

Tabs bent in to

 

Pipe

rest against pipe

 

 

 

 

Attic Insulation Shield

 

 

14-1/2 in. (368 mm)

 

6 Tabs bent

diameter

 

in 90°

Ceiling Firestop

 

 

Insulation

Pipe

Insulation

10-1/2 in.

(267 mm)

Figure 8.7 Install Attic Insulation Shield (firestop above ceiling)

 

 

Tabs bent in to

 

 

rest against pipe

 

Pipe

 

 

 

Attic Insulation Shield

 

 

14-1/2 in. (368 mm)

 

 

diameter

 

6 Tabs bent

 

 

in 90°

 

Insulation

 

Insulation

10-1/2 in.

Pipe

Ceiling Firestop

(267 mm)

 

 

Figure 8.8 Install Attic Insulation Shield (firestop below ceiling)

Heatilator • ST36D • 20396 • Rev AA • 11/08

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeatilator ST36D 20396 Rev AA 11/08 Appliance Certification Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceWood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for RemovalCheck Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Framing & ClearancesClearances Frame the Fireplace Sidewalls/SurroundsThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet AK14/AK18 Installation Install Outside Air KitChimney Assembly Meters Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldInstall Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in RoofFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST375 Square Termination Cap Install Termination CapTS345/TS345P Square Termination Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required= 1/k x inches of thickness FinishingHearth Extension Noncombustible Facing Finishing MaterialClearances to Mantels or other Combustibles above Fireplace Combustible MantelSquares Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace DimensionsCatalog # Chimney Components14-1/2 10-7/8 276 mm ST36D Service PartsContact Information

ST36D specifications

Hearth and Home Technologies ST36D is a stylish and efficient direct vent gas fireplace that has gained popularity among homeowners looking for an effective heating solution without compromising on aesthetics. This fireplace combines modern design with advanced technology, making it an attractive addition to any living space.

One of the standout features of the ST36D is its sleek, linear design, which offers a contemporary look suitable for a variety of home interiors. The fireplace comes in a 36-inch size, making it an ideal choice for both small and large rooms. Homeowners have the option to customize the front of the fireplace with different finishes and materials to match their décor, adding a personalized touch to their living space.

The ST36D is equipped with advanced direct vent technology that allows it to draw in air from outside for combustion while venting exhaust gases directly outside. This closed combustion system ensures maximum efficiency, reducing energy costs while providing consistent warmth. The direct vent feature also minimizes safety risks by preventing harmful gases from entering the home.

Performance-wise, the ST36D is built for efficiency, boasting an impressive thermal efficiency rating. The fireplace is designed to deliver a substantial amount of heat while maintaining a lower operating cost. Homeowners can expect effective heating, even in larger areas, thanks to its powerful output.

The ST36D includes a user-friendly remote control, allowing homeowners to operate the fireplace conveniently from anywhere in the room. The remote control enables adjusting flame height, heat output, and ambience settings with ease. Additionally, the fireplace can be integrated with home automation systems, providing further convenience in use.

Safety is also a key consideration in the design of the ST36D. It features an innovative safety barrier that helps prevent accidental contact with the heating elements. This makes it a great option for families with children and pets, ensuring peace of mind while enjoying the warmth of a flickering fire.

Overall, the Hearth and Home Technologies ST36D combines modern design, efficiency, and advanced technology, making it a top choice for anyone looking to enhance their home with a reliable and aesthetically pleasing gas fireplace. With its customizable features and safety measures, it effectively meets both functional needs and stylish aspirations.
Top Page Image Contents