Hearth and Home Technologies ST36D Seasoned Wood, Starting a Fire, Grate, Firescreen, Flue Damper

Page 8

B. Seasoned Wood

Properly seasoned wood is important for successful operation of your fireplace. Most woodburning fireplace problems are caused by burning wet, unseasoned wood.

Seasoned firewood is wood that is cut to size, split and air dried to a moisture content of around 20%.

Imagine a wooden bucket that weighs about eight pounds. Fill it with a gallon of water, put it in the fireplace and try to burn it. This sounds ridiculous but that is exactly what you are doing if you burn unseasoned wood.

A tree cut down a year ago and not split is likely to have almost as high a moisture content now as it did when it was cut.

Please refer to Section 2.M. for more detail.

C. Starting a Fire

NOTICE: You must establish a good draft to prevent smoke spillage into the room.

WARNING! Risk of Fire! Keep combustible materials, gasoline and other flammable vapors and liquids clear of the fireplace.

DO NOT:

•store flammable materials close to the fireplace

•use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

Keep all flammable liquids well away from the fireplace while it is in use. Combustible materials may ignite.

•The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the refractory and paint to cure. You may notice an industrial odor the first few fires. This is considered normal.

•Use well-seasoned wood.

•Open the flue damper to a fully open position.

•Place crumpled or twisted paper under the fireplace grate.

•Loosely arrange kindling or small pieces of wood to form a ‘tent’ on the fireplace grate.

•Pre-warm the flue to establish a draft to help reduce smoke spillage during start-up. Hold a rolled up piece of burning newspaper under the flue damper for a few moments.

•Light the crumpled paper to ignite the kindling.

•Add small pieces of wood until a hot bed of embers has been established.

•Add a minimum of three average size pieces of split firewood, placed to allow combustion air and flames between them.

CAUTION! Odors and vapors released during initial operation may be irritating to sensitive individuals.

Open windows for air circulation.

D. Grate

This fireplace is designed to be used with the grate sup- plied with this unit or one approved by HHT. The grate will break down over time and will need occasional replace- ment.

WARNING! Risk of Fire! Use only the factory-supplied integral grate.

•Keeps logs in place.

•Allows proper air circulation around the fire.

E. Firescreen

The firescreen is provided to control sparks. Keep it closed when the fireplace is in use.

WARNING! Risk of Fire or Burns!

•Screen will not prevent burning materials from falling out.

•Screen pulls or handles may be hot.

F. Flue Damper

•Refer to Figure 2.1 for location of control.

•Must be in fully open position (handle up toward the top of the fireplace) during operation of the fireplace.

•Before lighting the fireplace, verify fully open position by looking up from the inside of the fireplace.

WARNING! Risk of Fire and Asphyxiation! Open damper prior to operating fireplace. A closed damper overfires the fireplace and spills smoke and flames into the room.

G. Refractory

•The refractory is supplied to contain heat and provide an attractive interior.

•It will break down over time and will need occasional replacement. Small hairline cracks and discoloration are normal and do not affect its safety.

•(See refractory maintenance Section 3.C.)

WARNING! Risk of Fire! DO NOT burn fireplace with- out refractory. Use only refractory supplied by Hearth & Home Technologies, Inc.

8

Heatilator • ST36D • 20396 • Rev AA • 11/08

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeatilator ST36D 20396 Rev AA 11/08 Listing and Code Approvals Appliance CertificationNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Seasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Maintainance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for RemovalGlass Cleaning Check Firebox RefractoryInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Framing & Clearances Select Fireplace LocationClearances Sidewalls/Surrounds Frame the FireplaceInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK14/AK18 InstallationChimney Assembly Chimney Requirements MetersUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap Shrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield required= 1/k x inches of thickness FinishingHearth Extension Finishing Material Noncombustible FacingCombustible Mantel Clearances to Mantels or other Combustibles above FireplaceSquares Accessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsChimney Components Catalog #14-1/2 10-7/8 276 mm Service Parts ST36DContact Information

ST36D specifications

Hearth and Home Technologies ST36D is a stylish and efficient direct vent gas fireplace that has gained popularity among homeowners looking for an effective heating solution without compromising on aesthetics. This fireplace combines modern design with advanced technology, making it an attractive addition to any living space.

One of the standout features of the ST36D is its sleek, linear design, which offers a contemporary look suitable for a variety of home interiors. The fireplace comes in a 36-inch size, making it an ideal choice for both small and large rooms. Homeowners have the option to customize the front of the fireplace with different finishes and materials to match their décor, adding a personalized touch to their living space.

The ST36D is equipped with advanced direct vent technology that allows it to draw in air from outside for combustion while venting exhaust gases directly outside. This closed combustion system ensures maximum efficiency, reducing energy costs while providing consistent warmth. The direct vent feature also minimizes safety risks by preventing harmful gases from entering the home.

Performance-wise, the ST36D is built for efficiency, boasting an impressive thermal efficiency rating. The fireplace is designed to deliver a substantial amount of heat while maintaining a lower operating cost. Homeowners can expect effective heating, even in larger areas, thanks to its powerful output.

The ST36D includes a user-friendly remote control, allowing homeowners to operate the fireplace conveniently from anywhere in the room. The remote control enables adjusting flame height, heat output, and ambience settings with ease. Additionally, the fireplace can be integrated with home automation systems, providing further convenience in use.

Safety is also a key consideration in the design of the ST36D. It features an innovative safety barrier that helps prevent accidental contact with the heating elements. This makes it a great option for families with children and pets, ensuring peace of mind while enjoying the warmth of a flickering fire.

Overall, the Hearth and Home Technologies ST36D combines modern design, efficiency, and advanced technology, making it a top choice for anyone looking to enhance their home with a reliable and aesthetically pleasing gas fireplace. With its customizable features and safety measures, it effectively meets both functional needs and stylish aspirations.
Top Page Image Contents