W E A T H E R P R O O F M U T I N G S T E R E O V O L U M E C O N T R O L S
W E A T H E R P R O O F M U T I N G S T E R E O V O L U M E C O N T R O L S
AMPLIFIER’S MINIMUM SPEAKER LOAD IS 4 OHMS | AMPLIFIER S MINIMUM SPEAKER LOAD IS 8 OHMS |
8 OHM Speaker Pairs
10. Set the rubber gasket inside the faceplate and be sure it is |
seated properly. |
volume capability. Reduce the volume at once to avoid damaging your speakers.
| 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
|
|
| 0 | 1x |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 OHM | 0 |
|
| 1 | 2x |
|
| 4x |
|
|
|
|
|
|
|
|
|
|
| 1 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Speaker |
| ||||
| 2 |
|
|
|
|
| 8x |
|
|
|
|
|
|
| 4x | ||||
4 OHM |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Pairs | 2 | |||
Speaker | 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 |
| |
Pairs | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 |
|
| 5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 8 |
|
|
|
|
| Figure 3 |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| Figure 5 |
|
|
|
|
|
|
|
|
| Figure 6 |
|
|
2 | 3 | 4 | 5 | 6 | 7 | 8 |
4x 4x
8x
Figure 4
Figure 7
11. Use the shorter plate screws to fasten the gasketed faceplate |
to the volume control. DON’T OVERTIGHTEN THE PLATE |
SCREWS, WHICH COULD DAMAGE THE FACEPLATE. |
Align all the screws in the same direction for a clean, |
finished look. |
OPERATION
1.Make sure the amplifier or receiver power is OFF and set the volume to minimum.
2.Set the volume on the volume control to maximum (fully clockwise).
3.If you are using a Niles
4.Turn ON the amplifier or receiver and select a source, such as the tuner or CD player.
5.Slowly turn up the amplifier or receiver volume and set it to a comfortable – not maximum – listening level. Don’t over- drive or "clip" your amplifier. If the sound becomes muddy or distorted, you have reached the limit of your amplifier’s
6. | Use the volume control to adjust the volume of the speakers |
| to the desired listening level. If all the speaker pairs in your |
| system are equipped with Niles volume controls, you can |
| leave the amplifier or receiver volume set at one position |
| and use the Niles controls exclusively. |
7. | To mute the speakers without adjusting the volume control, |
| press the mute button. |
8. | To unmute speakers that have been muted, press the mute |
| button again. |
PROGRAMMING CAPABILITY
You can program individual WMVC 100 and WMVC 100E Muting Volume Controls attached to an MVC HUB4, allowing certain locations (such as the guest bedroom and porch) to remain muted when system activation turns on other locations (such as the kitchen and family room).
To program a WMVC 100 or WMVC 100E for automatic muting or unmuting, press and hold the mute button for 10 seconds. An LED blinks to indicate that programming has occurred.
The WMVC 100 and WMVC 100E come from the factory pre- programmed in the automatic mute mode.
7 | 8 |