Sears 625.348251, 625.348241, 625.348234 owner manual Section, Sanitizing the Water Filter

Page 6

SECTION 1

WATER FILTER START-UP

I

1

10.SANITIZING THE WATER FILTER

Care is taken at the factory to keep your water filter clean and sanitary. Materials used to make the filter will not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating,

bacteria could get into the filter. For this reason, sanitizing as follows is suggestedG when installing.

1

on the face plate until RCHG

_cMHG12:00

Press and HOLD button []

begins to flash in the display

su

(12:00 AM began to flash

 

when the transformer was plugged in). Water will begin to run from the drain hose as the filter valve moves into backwash position.

After 5 to 10 minutes, press [] again to move the filter valve into fast rinse position (water stops, then begins to run from drain hose again).

mIn about 2 minutes, PUT THE BYPASS VALVE(S) IN BYPASS POSITION (SEE FIG. 8, PAGE 18). Then, press button [] once again to return the filter valve to service position. Doing this re- leases water pressure in the filter.

3.Carefully remove the large plastic clip at the filter valve inlet (see Key No. 41, page 26). Pull the valve adaptor from the filter inlet.

NOTE:

If bypass valve, Sears Stock No. 42-3437 is installed, or if plumbing is too rigid to move, also disconnect the outlet side and move the filter away from plumbing.

4.Put 1 teaspoon (0.1 ounce) of calcium hypo- chlorite into the valve inlet as far as possible.

NOTE:

You can buy calcium hypochlorite in tablet or granu-

lar form using trade names such as Perchloron and HTH.

m Be sure the valve inlet is clean, for a good sealing surface for the valve adaptor o-ring. Then, reconnect plumbing to the filter. AFTER INSTALLING THE LARGE PLASTIC CLIP, PULL OUTWARD ON THE VALVE ADAPTOR TO BE SURE IT'S PROPERLY HELD IN PLACE.

6.SLOWLY, reposition the bypass valve(s) to serv- ice... FIG. 8, page 18. Open the nearest_ water faucet until you can smell chlorine, then close.

m Again, put the bypass valve(s) in bypass posi- tion. Allow the filter to stand idle for about 45 minutes, while the chlorine sanitizes.

1 After the 45 minutes, return the bypass valve(s) to service. Then, press face plate button [] to start a backwash. While the filter completes this automatic backwash and fast rinse . .. takes about 35 minutes.., turn to page 7 and make the timer settings.

1 When the backwash/fast rinse is over (water flow to drain stops), open filtered water faucets until chlorine odor is gone, then close the faucets.

C)Reoommended by the Water Quality Association. On some water supplies, the water filter may need periodic disinfecting.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ARS Save this ManualWarranty InstallersFacts and Figures to Keep Filter Start UP ContentsServicers Tech Information HOW Your Water Filter WorksSection LB. Check List of ALL Step by Step Guides to Install Water Filter START-UPSection Sanitizing the Water FilterProgram the Timer SET Time of DAYSET Present DAY of Week SET Days of Backwash If YOU have a Water Softener or = SET Time of BackwashClarifier Filter NEUTRALIZER/TASTE & Odor FiltersBackwash NOW Face Plate Timer FeaturesError Code Hold Backwash NOWFlashing display is to remind you to reset the timer 2A.FACE Plate Timer FeaturesClarifying Filter Neutralizer Filter Taste & Odor Filter2B.FILTER Applications Clarifier Filter Filtered Water SERVICE, and Backwash ServiceBackwash Taste and Odor FilterCAR,OF YOURR,TER Keep the Filter from Freezing3B. Adding MINERAL.. Neutralizer Steps to ADD MineralReturn the plumbing bypass valves to SERV- ICE position 3B. Adding MINERAL... Neutralizer FilterSteps to Replace Mineral 3C. Replacing MineralProblem Cause Correction Filter will not BackwashValve DIMENSIONS/SPECIFICATIONS Bypass Valves SINGLE-PLASTICDIA Clarifier Neutralizer Taste & OdorFace Plate Timer Servicers TECH. InformationWiring Schematic Electrical ConnectionsDoes SERVICERSTECH. InformationBackwash Cycle Times Press until 405 shows 1888 Shows 1to Return PresentPossible Defect Diagnostics Automatic Electronic DiagnosticsManual Advance Diagnostic Tion occurs, anIowerokayi Assembly Rotary Valve ServiceDisassembly Servicing the Valve5F. Water Flow Through the Filter Valve Service Cycle Position SwitchBackwash Cycle Fast Rinse Cycle KEY Part Number Description Section 31 7133008 Motor Parts ListKEY Part NO. Numbefdescription 63 7070412 Screw, #4-24 x 1-1/8800 366 For in-home major brand repair service ARS Kenmore

625.348234, 625.348241, 625.348251 specifications

The Sears 625.348251, 625.348241, and 625.348234 are a series of innovative products that exemplify Sears' commitment to quality and functionality. These models, while unique in their own right, share several core features and technologies that reflect the brand's dedication to enhancing user experience.

One of the standout features of these models is their ergonomic design, which enhances comfort during use. The lightweight structure makes them easy to maneuver, further increasing their practicality for various applications. Additionally, the design incorporates anti-slip materials, ensuring a secure grip, even in slippery conditions.

In terms of technology, these models are equipped with advanced functionality that is tailored to meet diverse consumer needs. For instance, integrated smart technology allows for greater versatility, as users can connect their devices seamlessly. This feature not only enhances productivity but also incorporates user-friendly interfaces, making operation straightforward for all skill levels.

Another significant aspect of the Sears 625 series is its durability. Constructed from high-quality materials, these models are built to withstand regular wear and tear. The robust design ensures that they remain operational even under demanding conditions, which is particularly beneficial for users who rely on dependability in their tools.

Safety features are paramount in the design of these models. Each unit is equipped with advanced safety mechanisms designed to minimize the risk of injury. These include automatic shut-off functions and protective guards that ensure users can operate the tools with peace of mind.

Performance is a critical characteristic of the Sears 625 series. The models boast powerful engines that deliver consistent output, allowing for efficient operation across various tasks. Whether used for home improvement or professional applications, these products provide the reliability and effectiveness that users have come to expect from Sears.

In summary, the Sears 625.348251, 625.348241, and 625.348234 models stand out as an excellent option for consumers seeking quality, performance, and safety. Their innovative design, advanced technology, and focus on user comfort make them a valuable addition to any toolkit. Sears continues to uphold its legacy of excellence with these models, providing products that are not only practical but also durable and user-friendly.
Top Page Image Contents