Jl. THERMOSTAT CABLE NSTALLATION
The thermostat for this cooler is connected to the cooler by
means of a 6 conductor thermostat cable (not provided).
Type CL2, 18 or 20 gauge, UL listed thermostat wire is recommended.
A_ Route one end of the thermostat cable (9) through the 1/2 'hole in the corner post on the left side of the access
door and then through the 1/2_'hole in the left end of the control box.
B, Insert the individual conductors of the thermostat ;wire
(9)into the terminal block connections on the right side of the printed circuit board (6). Connect colored wires to terminals as follows: white to '__C',brown to _H_,red
to _'L,green to '_Pyellow, to "D_,and blue to _'RTighten% screws.
C_ Install strain relief bushings (7) over the thermostat cable into the 1/2 °holes in the corner post and control box, allowing aslight amount of "slack', do not stretch the thermostat cable tight. Replace the control box cover - tighten the four screws.
D, Select a location for the thermostat
1. Mount the thermostat about 5 feet above the floor,
2, Mount the thermostat on a partitioning wall, not an
outside wail.
3_ Do not mount it near sources of heat,
4, Do not mount it in the direct draft of cooler air registers_
5Avoid dead air spaceswhich have titt[e air circulation,
E.Install the thermostat using the "Mounting Instructions for Thermostat" furnished with the cooler,
8
L INSTA_C[_N DEL CABLE DEL TERMOSTATO
Eltermostato est_ conectado al enfriador pot medio de un a[ambre piano de 6 conductores tipo telefono de 66 pies de largo (9) induido en Jacaja,
A, | Guie una punta de[ cable de termostato (9) aitrav6s de[ |
| |
| aguiero de 1/2_ en el poste de el [ado izquierdo de [a |
| puerla de acceso y despu6s altrav6s del agujero de |
| 1/2 °de [a caja de controJes. |
B.[nserte el conectador en el socket proveido en eI tado izquierdo de[ circuito impreso (6)en la caia de contro[es.
C_ [nstaJee/sujeta cable (7) sobre el cable yen los aguieros de 1/2 _ en la esquina de[ gabinete yen ]a caja de contro[es. Deiando una prequena cantidad de cable, no estire et cable det termostato. Ponga la tapadera de [a caja de[ control con los cuatro tornillos.
D.Seleccione el tugar para el termostato.
1.MonteM a 5 pies de[ piso.
2, [nsta[ee[ termostato en u_a pared interior no en una pared que de al exterior.
3.No monte el termostato cerca de una fuente de calor 4_ No Io monte en ta corriente de aire directa de [as
parri[las de[ enfriador.
5.Evite espacios muertos de aire que tengan poquita circulaci6n.
E.Instate el termostato usando las "lnstrucciones para montar et termostato" proveidas con el enfriador.
|
|
|
|
|
|
| / |
|
|
| 7 | 6 |
|
|
|
|
|
|
|
| 9 | 4 | 3 | 2 | 1 |
|
|
|
|
| 5 |
|
|
|
|
|
|
| |
1. | Chase Nipple | 6, Printed Circuit Board | 1. Niple De Encaje | 6. | Conectador De Termostato | ||||
2, | Jam Nut |
|
| Thermostat Connector | 2. | Contratuerca |
| En ElCircuit() tmpreso | |
3. | Junction Box | 7, Strain Relief Bushings | 3. | Caja De Empalme | 7. | Sujeta Cables | |||
4 | Switch |
| 8, Cooler | cabinet | 4, lnterruptor | 8. | Gabinete | ||
5, junction | Box Cover | 9. Thermostat Cable | 5. Tapadera | 9. | Cable De Termostato | ||||