Sears 153.335914 Venting System Example Installations for ALL Models contd, Precautions, 50F

Page 17

Installation Instructions (cont'd)

VENTING SYSTEM EXAMPLE INSTALLATIONS FOR ALL MODELS (cont'd)

2. Horizontal runs require a minimum ¼" rise per foot.

35'Max. 16" MIN.

13" MIN.

Min. rise ¼"

I1" MIN.

per foot

3.A vertical run can be no more than 20'.

4.The total vertical and horizontal run cannot exceed 35'.

 

 

Min. rise ¼"

 

One Elbow

perfoot

Ma_ 20'

 

 

 

TOTAL VERTICAL AND

 

HORIZONTAL RUNS

 

CANNOT

EXCEED 35'

I

I

 

T

 

Min. rise ¼"

 

per foot

CEMENTING PVC, ABS OR CPVC PIPE AND FITHNGS

Read and observe all safety information printed on primer, cleaner, and cement containers.

DANGER

Primer, cleaner, and cements are extremely flammable.

They are harmful or fatal if swallowed. The vapors are harmful. They may irritate eyes and skin and can be absorbed through the skin.

PRECAUTIONS

Always store primers, cleaner, and cements in cool, dry, well ventilated places. Do not store them near heat, sparks, or flames. Keep containers closed. Use them in well ventilated areas. Wear impervious clothing while handling. Do not smoke, eat, or drink while handling. Wash thoroughly after handling and before eating. Wear

eye protection when handling. If swallowed, drink water, do not induce vomiting, and call a physician or poison control center immediately. If inhaled, get fresh air and seek medical attention if ill feelings persist. In case of

eye and skin contact, immediately flush with plenty of water for 15 minutes and seek medical attention if irri-

tation persists. KEEP OUT OR REACH OF CHILDREN.

All primers, cleaners, and cements must meet all local codes and

applicable standards of the American Society For Testing

Materials Standards.

Before using primers, cleaners, and cements, stir or shake, mak-

in sure contents are liquid. Do not use if found to be lumpy or jei_;-like.

1.Cut pipe ends squarely removing all burrs and dirt.

2.Dry fit pipe and fittings to be connected for proper fit.

3.Clean pipe and fitting with a primer/cleaner.

4.Apply a thin coat of cement to fitting, avoiding puddling inside.

5.Apply a liberal coat of cement to pipe leaving no voids.

6.QUICKLY assemble parts while cement is fluid! If you wait too long, re-coar pipes.

7.Push pipe completely into socket of fitting, turning as it goes until it bottoms.

8.Hold pipe and fitting together for 30 seconds. Then carefully clean off excess with a cloth. Allow connections a sufficient

time to cure before disturbing.

Max.20'

9. Remember that vent pipes must be adequately and securely

supported.

 

 

 

 

APPROXIMATE

SETTING TIME FOR 2½" TO 4" PIPE

 

OINTS

 

I

 

TOTAL VERTICAL AND

 

MOVEMENT

COMPLETE

 

HORIZONTAL RUNS

 

 

 

 

 

 

Min. rise ¼"

CANNOT EXCEED 35'

 

OF JOINT

SET

per foot

90°F to 150°F

3Ahr.

8

hrs.

 

50°F

to 90°F

1 hr.

15

hrs.

 

0°F

to 50°F

1_ hr.

18

hrs.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Injury Or Property DAM For Your SafetyAN Odorant is Added to the GAS Used by this Water Heater DEATH, Serious Bodily INJURY, or Property Safety PrecautionsDEATH, Serious Bodily INJURY, or Property Damage Safety Precautions onAE,WARNING Obstructed or deteriorated vent systems may present aVent termination must not be within 4 feet of any items J AwarningSuch as gas meters, gas valves or other gas regulating J EquipmentContents 40,000 Customer ResponsibilitiesProduct Basic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Removing the Old Water Heater Installation InstructionsLocating the New Water Heater Water Heaters Eventually Leak InstallationofWhile this may reducethe changesof flammable vaporsfrom a Heater adjacentto the gascontrolvalvefor all clearanceWhen determining the installation location for apower vent Installation Instructions contdHne. b Outlet vent. bALL AIR from Inside Buildings For Appliances Located in Confined SpacesWater Piping Installation Completed UsingMust take spechl precaon In addition to using Reliefvalve Opening Temperature-Pressure Relief ValveUSE with Power Cord WiringUSE Without Power Cord Filling the Water HeaterSion or asphyxiation Installation Instructions contdVenting PVC Schedule 40 Vent Piping Venting System Example Installations for ALL ModelsVenting contd Precautions Venting System Example Installations for ALL Models contdMaterials Standards 50FInstallation Showing USE of PVC, ABS or Cpvc Pipe Connecting PVC, ABS or Cpvc Pipe Vent to BlowerAppliance and its gas connection must GAS Piping with Flexible ConnectorBeforeplacingthe appliancein operation Code,ANSI Z223.1,also referred to as NfpaContd Installation ChecklistBefore Lighting the Pilot Check for LeaksOperation Operating InstructionsLighting Operating InstructionsA fire or explosion Operating Instructions contdWhatto Doif Yousmellgas Hotter Water can SCALD,Water heatersare intendedto Temperature RegulationTank Sediment Cleaning Service and AdjustmentVenting System Inspection Oiling InstructionsAssembly Replacement Service and Adjustment contdGas Control Valve & Burner InformationHousekeeping Drain Valve Washer ReplacementService Start Up Conditions Troubleshooting GuideThermal Expansion Strange SoundsTroubleshooting Guide contd Leakage Checkpoints Page Power 9OO1993 90019579001959 90O1960This is a REPAIRPARTSLIST, not a Packing List 153.335914 153.33584442-9231 9001987RERS.IR Part

153.335815, 153.335961, 153.335903, 153.335915, 153.335803 specifications

Sears has long been a household name in American retail history, with its roots dating back to the late 19th century. The brand has transformed over the years, adapting to changing consumer needs and market trends, and its products have evolved with advancements in technologies and consumer preferences.

At the core of Sears' appeal has traditionally been its diverse range of offerings, from appliances and tools to clothing and home goods. In particular, Sears has been known for its line of Kenmore appliances, which are celebrated for their reliability and efficiency. The Kenmore brand has continually introduced innovative technologies that enhance user experience, such as energy-efficient washing machines and smart refrigerators that can be monitored from smartphones.

Sears has also been at the forefront of implementing retail technologies. The use of barcode scanning and point of sale systems streamlined the shopping experience, allowing for quicker checkouts and more accurate inventory management. Additionally, Sears embraced e-commerce early in the internet revolution, providing customers with online shopping options that catered to the growing demand for convenience.

Another distinguishing feature of Sears is its commitment to private label brands, such as Craftsman and DieHard, known for their quality and performance. Craftsman tools have been a staple for DIY enthusiasts and professionals alike, offering a wide range of products from hand tools to power equipment. Similarly, DieHard batteries are synonymous with reliability, making them a top choice for consumers when it comes to automotive needs.

In recent years, Sears has faced significant challenges due to shifts in retail shopping behavior, with many consumers moving to online platforms and discount retailers. Despite this, the company is working to modernize its approach, focusing on the integration of an omnichannel strategy that marries in-store and online shopping experiences.

With the ongoing evolution of retail, Sears continues to adapt, leveraging its history and brand recognition while exploring new technologies and methods to capture the attention of a modern consumer base. Whether through enhancing its product offerings or embracing the latest retail technologies, Sears remains a significant player in the retail landscape, aiming to navigate the changing tides of consumer preferences and market conditions.
Top Page Image Contents