Graco 308791E Table of Contents, Setup, Install the Elbow Fitting and Tubing, Parts

Page 2
Table of Contents

Table of Contents

Set-Up

. . . . 2

Double Air Reg. Assembly 235376

. . . . . 8

Operation

. . . . . 4

Remote Single Air Reg. . . . . . . . . . . . . . . . . . . . . . 9

Maintenance

. . . . . 6

Pressure Cup Kit 239804

. . . . . 9

Parts

 

Remote Single Air Reg. Assembly 236142

. . . . . 9

One Quart Pressure Cup 239801

. . . . . 7

Technical Data

. . . . 10

Single Air Reg

7

Accessories

. . . . 11

Pressure Cup Kit 239802, 245181

. . . . . 7

Warranty

. . . . 12

Single Air Reg. Assembly 235375, 245192

. . . . . 7

Graco Information

. . . . 12

Double Air Reg. Pressure Cup Kit 239803 .

. . . . . 8

 

 

Setup

NOTE: Tighten all fittings securely.

Install the Elbow Fitting and Tubing

Push the tubing (3), with the check valve (13), firmly into the cup’s elbow fitting (D). See Fig. 2 or 3. The tapered side of the check valve must face towards the cup’s elbow fitting.

NOTE: To disconnect the tubing, push down on the fitting’s outer ring and pull on the tubing.

Part No. 239802, 239803, and 245181: Install the Gun on the Cup

1.Tighten the cup swivel fitting (E) onto the gun fluid inlet. See Fig. 2.

2.Tighten the air fitting (F) onto the gun air inlet.

Part No. 239804: Assemble the Remote Single Air Regulator Pressure Cup Kit

1.

Tighten the cup swivel fitting (E) onto the fluid

 

outlet fitting (4) of the air regulator assembly. See

 

Fig. 3.

2.

Tighten the air supply line (G) onto the air inlet

 

fitting (19).

3.

Tighten the air line (H) onto the gun air inlet.

Fill the Pressure Cup

1.Push the clamp lever (A) fully to the unclamped position, against the yoke (B). See Fig. 1.

2.Twist the cup lid (101) counterclockwise to disen- gage the yoke hook from the cup extended pins (C).

3.Remove the cup lid (101) and fill the cup with fluid.

4.Twist the cup lid (101) clockwise to engage the yoke (B) hook, then push the clamp lever (A) fully to the clamped position. Use your thumb to force the clamp lever into position; do not use wrenches or tools to move it.

A

101

B

C

103

4. Tighten the fluid line (J) onto the gun fluid inlet.

Fig. 1

01961A

2 308791

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Single Air Regulator Instructions - Parts ListImportant Safety Instructions Double Air RegulatorInstall the Elbow Fitting and Tubing Table of ContentsSetup Part No. 239802, 239803, and 245181 Install the Gun on the Cup7612A 3087917611A 7623APressure Relief Procedure Setting the Cup Air PressureSetting the Gun Air Pressure OperationOptional Gun Air Regulator Disconnect the Gun and Air Regulator from the Cup Maintenance1. Follow the Pressure Relief Procedure Warning on page Remove the Cup LidSee parts list at right Use Only Genuine Graco Parts and AccessoriesSingle Air Regulator Assembly Part No. 235375, Series B See parts list aboveSee parts list, page Double Air Regulator Assembly Part No. 235376, Series BSee parts list below Double Air Regulator Pressure Cup KitPressure Cup Kit Remote Air Regulator AssemblyRemote Single Air Regulator Part No. 236142, Series BWeight without gun Technical DataWeight Single Air Regulator Pressure Cup Kit, Part No. 239802 and100 psi 7 bar Maximum Outlet Pressure AccessoriesSpray Gun Air Regulator Assembly 150 psi 10 bar Maximum Inlet PressureFOR GRACO CANADA CUSTOMERS Graco Standard WarrantyGraco Information Graco reserves the right to make changes at any time without notice
Top Page Image Contents