Lux Products PSP711TS warranty Batteries and Maintenance, Technical Assistance Warranty

• Maximum Smart Recovery time is one hour.

8. BATTERIES AND MAINTENANCE

3.6. WIRING DIAGRAMS

• The Smart Recovery temperature set point must

be achievable. If a desired smart recovery is

repeatedly ignored by your thermostat. That is an

indicator that you should modify your program so

that the recovery can be achieved within the 1

hour limit.

• A Smart Recovery may not be initiated for 48

hours after the units programs have been

changed. This allows the unit to gather the data

necessary to predict a Smart Recovery time.

7.3. TEMPERATURE DISPLAY FORMAT

˚F/˚C SWITCH #3

The position of this switch controls whether the

temperature is displayed in degrees ˚F or ˚C.

7.4.5 MIN / 2 MIN MINIMUM RUN TIME SWITCH #4

The position of this switch controls minimum length of time the thermostat must remain with Heat or Cool either ON or OFF before it will automatically switch to the alternate ON or OFF state. This feature prevents short cycling and provides compressor protection for cooling units. Choices are 2 or 5 minutes.

7.5.REPOSITIONING SWITCHES

Use this table to determine the positions which correspond to the operation you prefer.

	12hr	SR=OFF	F	5min
	24hr	SR=ON	C	2min
U4	1	2	3	4

This table is printed on the circuit board. To change a switch position move switch down or up. After settings have been changed with batteries installed, press the Hardware Reset (H.W. Reset) button on the rear of the unit's circuit board for changes to take effect. See jumper and switch positions figure on Page 12.

7.6. GAS/ELECTRIC JUMPER

The PSP711TS requires batteries to operate your heating/cooling system. Replace the batteries when the battery REPLACE indicator appears in the display or at least once a year.

1.To access your units batteries remove the unit from the wall by pressing up on the thumb latch at the bottom of thermostat and swinging the body up and away to remove it from the wall.

2.Remove the used batteries. See battery location and polarity in figure on Page 12.

3.Install two new Energizer® or DURACELL® "AA" size alkaline batteries in the battery compartment. Observe the polarity marking shown in the compartment.

4.Hang the top of the unit by the tabs at the top corners of the base, then snap the bottom of the unit into place. Do not use unnecessary force. If the body does not snap into place easily, remove the body, re-hang it from the tabs and try again.

9. TECHNICAL ASSISTANCE

If you have any problems installing or using this thermostat, please reread the instructions carefully or visit our online technical support at www.luxproproducts.com. If you require assistance, please call our Technical Assistance number between 8:00 a.m. and 4:30 p.m. Eastern Standard Time, Monday through Friday. The number is (856) 234-8803.

10. WARRANTY

Limited Warranty: If this unit fails because of defects in materials or workmanship within one year of date of original purchase, LUX will, at its option, repair or replace it. This warranty does not cover damage by accident, misuse, or failure to follow installation instructions. Implied warranties are limited in duration to one year from date of original purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

2 + 3 WIRE HEATING SYSTEMS

	JUMPER
	PROVIDED
W Y	G B O	RC RH C
W	G	RH	COMMON
		RC	FOR
		R
			SYSTEM
H	F	V
			POWER
4		5

NOTE: "G" WIRE IS

OMITTED FOR

2 WIRE SYSTEMS

HEATING/COOLING SYSTEMS

5 + 6 Wire 2 Transformers

					JUMPER
					REMOVED
W Y		G	B	O	RC RH C
W	Y	G	B*	O	RC RH	COMMON
					R	FOR
H	C*	F			V
						SYSTEM
4	6				5
						POWER

COOLING SYSTEMS

JUMPER

PROVIDED

W Y G B O RCRH C

					COMMON
	Y	G	RH
				R	FOR
					SYSTEM
C*		F		V
6					POWER

HEATING/COOLING SYSTEMS

4 + 5 Wire 1 Transformers

JUMPER

PROVIDED

W Y G B O RCRH C

									COMMON
	W		Y	G	B*	O	RH
							RC		FOR
	H	C*		F				R	SYSTEM
								V
4		6					5		POWER

In HEAT mode, the position of this jumper controls when the thermostat requests the system fan to run. In Gas mode the fan is normally controlled by the heating system itself. In Electric mode, the fan is controlled by the thermostat. See jumper and switch positions figure on Page 12.

Please return malfunctioning or defective units to the participating retailer from which purchase was made, along with proof of purchase. Please refer to "Technical ASSISTANCE" before returning thermostat. Purchaser assumes all risks and liability for incidental and consequential damage resulting from installation and use of this unit. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Applicable in the U.S.A. only.

8

WIRING DIAGRAM NOTES (APPLIES TO ALL DRAWINGS)

*Verify whether “C”, “X” or “B” wires are connected to system common.

*If “B” and “O” are both present, it is likely that “B” is a system common.

*If a “B” wire in your system is a common, then connecting it to the “B” terminal may cause damage to your system.

*If “Y” and “C” are both present, it is likely that “C” is a system common.

*Use an optional common wire to allow the system to power your thermostat.

9