Cadet EBKA-1-24 installation instructions Installation Instructions, Operation, Warranty

READ ALL

INSTRUCTIONS

AND SAFETY

INFORMATION.

WARNING! Risk of electrical shock. Turn off all power at the electrical panel board supplying power to the heater before doing any electrical wiring.

WARNING! Do not hit or damage the temperature limit

sensing switch on this heater.

WARNING! Do not operate the heater without the front cover in place.

IMPORTANT! It is extremely important that you verify the electrical supply wires are the same voltage as the heater (i.e. 120 volt heater to 120 volt power supply and 240 volt heater to 240 volt power supply).

Installation Instructions

1.Remove the heater front panel by lifting up and pulling out on the bottom edge of the front panel. Set the front panel aside.

2.Remove the junction box cover at the left end of the heater by removing the screw (See Figure 1). Keep screw for future use.

3.If you are installing the EBKA-1-24 thermostat kit as part of a new installation, proceed to Step 6.

4.Disconnect the power supply wires and remove the wiring strain relief device from the heater.

5.Remove heater from the wall by lifting the heater off the mounting brackets. It is best to replace the thermostat while the heater is not mounted.

6.Remove the existing left end cap or EBKA-1-24 thermostat kit by removing the screw and clip located on the back of the heater and sliding the end cap away from the heater. Keep screw and clip for future use.

7.Attach the new EBKA-1-24 thermostat kit with the indicator light on top by sliding it onto the heater, making sure no wires are caught between the thermostat and heater. Secure in place using the screw and clip previously removed in Step 6.

8.Route power supply wires through the

	wiring knockout hole and secure to heater	PILOT			BLACK
	using the strain relief connector. If this is a
	new unit, refer to the EBHA owner’s guide	LIGHT		BLACK						ELEMENT
	for instructions on how to install the heater.	EBKA-1-24
9.	Attach heater to the wall mounting	THERMOSTAT								TERMINALS
	brackets, making sure the power supply
	wires are not pinched between the wall		RED RED				CRIMP
	and the heater.						CONNECTOR
10.	Connect one red wire from the thermostat
	to one power supply wire. Connect
	remaining red wire from thermostat to
	remaining power supply wire.					CRIMP		LIMIT	CONTROL
		SUPPLY WIRES
11.	Connect one black wire from the					CONNECTOR
	thermostat and one black wire from the
	indicator light to one black wire from the heater. Connect the remaining black wire from the thermostat
	and black wire from the indicator light to the remaining black wire from the heater.

12.Connect ground to grounding screw provided in junction box. Note: All wires must be used.

13.Inspect all wire connections to be sure they are fastened securely. Push wiring back into the junction box and re-attach the junction box cover using screw previously removed.

14.Reattach the heater front panel and turn the thermostat to the lowest position.

15.Restore power at the electrical panel board (circuit breaker or fuse box).

16.Rotate the thermostat control knob to a higher setting until the indicator light turns on.

IMPORTANT: All wiring must comply with all local electrical codes.

Operation

How to operate your thermostat

1.Once installation is complete and power has been restored, turn the thermostat knob to the highest position.

2.When the room reaches your comfort level, slowly turn the thermostat knob down to a lower setting until the light goes off or a click sound is heard. The heater will automatically cycle around this preset temperature.

3.To reduce the room temperature, turn the knob to a lower setting. To increase the room temperature, turn the knob to a higher position.

Warranty

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet product, including thermostats, found to be defective within one year after the date of purchase.

These warranties do not apply:

1.Damage occurs to the product through improper installation or incorrect supply voltage;

2.Damage occurs to the product through improper maintenance, misuse, abuse, accident, or alteration;

3.The product is serviced by anyone other than Cadet.

4.If the date of manufactur e of the product cannot be determined;

5.If the product is damaged during shipping through no fault of Cadet.

6.CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROPER TY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.

7.IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS DOES NOTMODIFY OREXTENDTHE UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WARRANTIES.

8.These warranties give you specific legal rights, and you may also have other rights which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein.

If you believe your Cadet product is defective, please, contact Cadet Manufacturing Co. at 360-693-2505, during the warranty period, for instructions on how to have the repair or replacement processed. Warranty claims made after the warranty period has expired will be denied. Products returned without authorization will be refused.

Parts and Service

Visit www.cadetco.com/parts_service for information on where to obtain Parts and Service.

2 ©2007 Cadet Manufacturing Co. Printed in U.S.A. Rev. 11/07 #706982