Remote Receiver, REV.1/25/05 Page 3 of 9

THERMO UPDATING FEATURE –TRANSMITTER – (T/S –TX)

This ECS remote control has a THERMO UPDATING Feature built into its software. The THERMO UPDATING Feature operates in the following manner, but only in the THERMO MODE:

The transmitter normally reads the ROOM temperature every 2 minutes checking the ROOM temperature against the SET temperature and then sends a signal to the receiver.

COMMUNICATION – SAFETY – TRANSMITTER – (C/S – TX)

This ECS remote control has a COMMUNICATION –SAFETY function built into its software. It provides an extra margin of safety when the TRANSMITTER is out of the normal 20 foot operating range of the receiver.

The COMMUNICATION – SAFETY feature operates in the following manner, in all OPERATING MODES – Manual ON and THERMO.

At all times and in all OPERATING MODES, the wall transmitter sends an RF signal every fifteen (15) minutes, to the receiver, Should the receiver NOT receive a transmitter signal every 15 minutes, the IC software, in the RECEIVER, will begin a 2- HOUR (120-minute) countdown timing function. If during this 2-hour period, the receiver does not receive a signal from the wall transmitter, the receiver will shut down the appliance being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps” for a period of 10 seconds. Then after 10 seconds of rapid beeping, the RECEIVER will continue to emit a single “beep” every 4 seconds until the ON button on the wall transmitter is pressed to reset the receiver. The intermittent 4 second beeping will go on for as long as the receiver’s batteries last which could be in excess of one year.

To “reset” the RECEIVER and operate the appliance, you must press ON button on the wall transmitter. The flame icon must be display on the LCD screen. By turning the system to ON, the COMMUNICATION -SAFETY operation is overridden and the system will return to normal operation depending on the MODE selected at the wall transmitter. The COMMUNICATION – SAFETY feature will reactivate if the transmitter’s batteries fail or be removed.

REMOTE RECEIVER

The remote receiver operates on 4 AA-size 1.5V batteries. It is recommended that ALKALINE batteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential for proper operation of the remote receiver.

The remote receiver houses the microprocessor that responds to commands from the transmitter to control system operation. It emits one beep when it receives an ON or OFF command manually, but no beep when cycling on and off automatically in THERMO mode. The remote receiver has a 3-position slide switch for selecting the MODE of operation: ON/REMOTE/OFF

•With the slide switch in the ON position (toward the LEARN button), the system will remain on until the slide switch is placed in the OFF or REMOTE position.

•With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver receives commands from the transmitter.

•With the slide switch in the OFF position (away from the LEARN button), the system is off.

•It is suggested that the slide switch be placed in the off position if you will be away from your home for an extended period of time. If the remote receiver is mounted out of children’s reach, placing the slide switch in the OFF position also functions as a safety

“lock-out” by both turning the system off and rendering the remote receiver inoperative.

THERMO- SAFETY FEATURE – RECEIVER (T/S –RX)

This ECS remote control has a THERMO- SAFETY feature that is built into the system’s RECEIVER. This feature is temperature- activated and provides an extra margin of safety when the RECEIVER is operating where ambient temperatures exceed 130 0 F degrees inside the receiver case.

The THERMO-SAFETY feature, in the RECEIVER, operates in the following manner, when the appliance is in operation.

The receiver is thermally protected from extreme heat conditions. Heat can have negative effect on the operation of the receiver’s microprocessors.

REV.1/25/05 Page 3 of 9 Part #17810

TRW-1 specifications

The Elitegroup TRW-1 is a pioneering solution in the realm of gaming and content creation, designed to cater to the demands of modern users who prioritize performance and reliability. This advanced motherboard has garnered attention for its cutting-edge features and robust technologies, making it a preferred choice for both enthusiasts and professionals.

One of the defining features of the TRW-1 is its comprehensive support for the latest Intel processors, ensuring compatibility with a wide range of powerful CPUs. This flexibility allows users to harness the full potential of the latest multi-core technology, which is particularly beneficial for demanding tasks such as gaming, video editing, and 3D rendering.

The TRW-1 is equipped with a state-of-the-art power delivery system, featuring high-quality capacitors and multiple phases dedicated to CPU power. This design ensures stable voltage and enhanced efficiency, allowing for better performance even under heavy loads. Additionally, the motherboard is designed with improved thermal management solutions, including heatsinks and strategically placed fan headers, which help maintain optimal temperatures during intense usage.

Connectivity is another highlight of the Elitegroup TRW-1, as it includes support for the latest PCIe 4.0 standard. This feature allows for lightning-fast data transfer speeds with modern graphics cards and SSDs, further elevating gaming experiences and productivity levels. The TRW-1 also supports high-speed DDR4 memory, with multiple DIMM slots accommodating substantial amounts of RAM, which is essential for multitasking and resource-heavy applications.

In terms of expansion, the TRW-1 features a well-designed layout that includes multiple PCIe slots for additional expansion cards, making it easy for users to enhance their systems with additional GPUs, sound cards, or networking capabilities.

For storage, the TRW-1 supports numerous SATA and M.2 slots, giving users the flexibility to configure their storage according to their specific needs. The inclusion of advanced storage technologies, such as RAID support, ensures data redundancy and improved performance.

Overall, the Elitegroup TRW-1 stands out in the crowded motherboard market by combining leading-edge technologies, excellent performance characteristics, and user-friendly features. Its balance of power, connectivity options, and expandability make it a compelling choice for anyone looking to build a high-performance PC. Whether for gaming, content creation, or professional applications, the TRW-1 delivers a reliable and robust platform that meets the needs of today’s users.