Elitegroup TRW-1 installation instructions Installation and Operating Instructions, Introduction

Page 1

ECS

TRW-1

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT

ATTEMPT TO INSTALL OR OPERATE

INTRODUCTION

This ECS’s remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio frequencies (RF) within a 20'’range using non-directional signals. The system operates one of 1,048,576 security codes that are programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY SECTION under TRANSMITTER section and THERMO SAFETY SECTION under REMOTE RECEIVER section. These signal/temperature safety features shut down the fireplace system when a potentially unsafe condition exists.

WALL MOUNT THERMOSTAT

LCD

DISPLAY

ROOM “SET” TEMP

THERMO

MODE

The wall/transmitter operates on (2) 3V Button Cell (Included) which powers the LCD screen and powers the RF signal. These batteries are made specifically for remote controls and electronic lighters. Before using the transmitter the 3V batteries must be installed into the battery compartments.

It is recommended that CR2032 lithium batteries always be used for longer battery life and maximum operational performance.

SET

ECS

BUTTON

 

ON/UP

SET

BUTTON

 

ON

OFF

OFF/DOWN

 

BUTTON

 

Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the LCD screen will not come on, check the 3V Button Cell battery.

TO INSTALL BATTERIES IN THE WIRELESS THERMOSTAT

1.Remove face from backing plate This is done by sliding the face up about 1/2” then pull the face off the base plate. As shown in Figure #1

2.Locate the (2) holders for the 3V button cell batteries.

3.Slide the button cell batteries into the battery holders. (Make sure that the batteries are installed with the (+) plus side facing you or up.

TO REMOVE THE BATTERIES IN THE WIRELESS THERMOSTAT

1.Remove face from backing plate This is done by sliding the face up about 1/2” then pull the face off the base plate. As shown in Figure #1

2.Locate the (2) holders for the 3V button cell batteries.

3.Insert a small screwdriver into the slot above the button cell battery and push the battery out. AS shown in Figure #2

Figure #1

Figure #2

 

BACK OF UNIT

 

ROOM

TEMP

 

 

 

ECS

ON

SET

 

OFF

 

 

Battery Removal

 

 

Slots

+

+

REV.1/25/05 Page 1 of 9 Part #17810

Side

Side

Plus

Plus

 

(2)3 Volt Button Cell Batteries

Page 1 Page 2
Image 1
Page 1 Page 2
Contents To Install Batteries in the Wireless Thermostat Installation and Operating InstructionsTo Remove the Batteries in the Wireless Thermostat IntroductionREV.1/25/05 Page 2 of 9 General InformationCommunication Safety Transmitter C/S TX Thermo Updating Feature -TRANSMITTER T/S -TXTHERMO- Safety Feature Receiver T/S -RX Remote ReceiverInstallation Installation InstructionsREV.1/25/05 Page 4 of 9 Wall MountingWiring Millivolt Valves Wiring InstructionsREV.1/25/05 Page 5 of 9 Hearth MountREV.1/25/05 Page 6 of 9 System CheckTrouble Shooting Battery LifeReceiver Adjustment Recommended Adjustment REV.1/25/05 Page 7 of 9FCC Requirements SpecificationsManufactured Exclusively by Skytech II, INC REV.1/25/05 Page 8 of 9REV.1/25/05 Page 9 of 9 Remote Wall Thermostat Receiver Installation Instructions

TRW-1 specifications

The Elitegroup TRW-1 is a pioneering solution in the realm of gaming and content creation, designed to cater to the demands of modern users who prioritize performance and reliability. This advanced motherboard has garnered attention for its cutting-edge features and robust technologies, making it a preferred choice for both enthusiasts and professionals.

One of the defining features of the TRW-1 is its comprehensive support for the latest Intel processors, ensuring compatibility with a wide range of powerful CPUs. This flexibility allows users to harness the full potential of the latest multi-core technology, which is particularly beneficial for demanding tasks such as gaming, video editing, and 3D rendering.

The TRW-1 is equipped with a state-of-the-art power delivery system, featuring high-quality capacitors and multiple phases dedicated to CPU power. This design ensures stable voltage and enhanced efficiency, allowing for better performance even under heavy loads. Additionally, the motherboard is designed with improved thermal management solutions, including heatsinks and strategically placed fan headers, which help maintain optimal temperatures during intense usage.

Connectivity is another highlight of the Elitegroup TRW-1, as it includes support for the latest PCIe 4.0 standard. This feature allows for lightning-fast data transfer speeds with modern graphics cards and SSDs, further elevating gaming experiences and productivity levels. The TRW-1 also supports high-speed DDR4 memory, with multiple DIMM slots accommodating substantial amounts of RAM, which is essential for multitasking and resource-heavy applications.

In terms of expansion, the TRW-1 features a well-designed layout that includes multiple PCIe slots for additional expansion cards, making it easy for users to enhance their systems with additional GPUs, sound cards, or networking capabilities.

For storage, the TRW-1 supports numerous SATA and M.2 slots, giving users the flexibility to configure their storage according to their specific needs. The inclusion of advanced storage technologies, such as RAID support, ensures data redundancy and improved performance.

Overall, the Elitegroup TRW-1 stands out in the crowded motherboard market by combining leading-edge technologies, excellent performance characteristics, and user-friendly features. Its balance of power, connectivity options, and expandability make it a compelling choice for anyone looking to build a high-performance PC. Whether for gaming, content creation, or professional applications, the TRW-1 delivers a reliable and robust platform that meets the needs of today’s users.
Top Page Image Contents