AMX ViewStat manual Mounting the Base to a Wall, Communications

Page 18

ViewStat Installation and Wiring

Communications

Wire to Protocol Adapter, other Distribution Panels or directly to Automation System

A:Transmit B: Receive

ADDRESS #

Rx+

Rx-

Tx+

Tx-

24VAC

GND

 

Switches

3

 

A - Allows Transmit

 

Communications

 

B - Allows Received

 

Communications

 

PWR - Turns power to

 

thermostat on/off

 

LEDs light when

 

2

communications are

 

REF

transmitted (A)

 

 

or received (B)

 

ADDRESS #

ADDRESS #

ADDRESS #

ADDRESS #

Transformer 24 V, 40 VA minimum up to 8 thermostats

C - 24 V (common) (-) if DC R - 24 V (hot) (+) if DC

1

Main Power Switch Turns main power to Distribution Panel on/off

ADDRESS #

ADDRESS #

4

ADDRESS #

LED will light up when

power to thermostat is switched on

FIG. 7 Wiring the VST-TSTAT to a VST-DIST Distribution Panel

Mounting the Base to a Wall

There are four screw holes located on the base of the thermostat; two are for a junction box mounting, along with two for alternate mounting spacing. Use one of the holes on the top and one on the bottom.

1.Place the base over the wire hole opening in the wall; level the base and mark the screw hole mounting locations (leveling required for appearance only).

2.If using supplied wall anchors, drill 3/16" hole in the center of the marked locations and tap in the wall anchors. If using the supplied screws only, drill a 3/32" hole in the center of the marked locations.

12

ViewStat Communicating Thermostat

Page 17 Page 19
Image 18
Page 17 Page 19
Contents ViewStat AMX Limited Warranty and Disclaimer Table of Contents Support Module Installation and Wiring Operating the Thermostat Table of Contents ViewStat Communicating Thermostat Product Information IntroductionSystem Components ViewStat SpecificationsViewStat Specifications System ComponentsEnclosure Support Module SpecificationsCircuit Board Components HWDVST-TTM and VST-TRH Remote Sensor Specifications Maximum Cable DistancesMaximum Cable Distances Hvac System Pre-Installation Check List Hvac System Pre-installation Check ListApplication # of Hvac Wiring Diagram Wires Product Information ViewStat Communicating Thermostat Selecting the Thermostat Location Disconnecting Power to All Hvac EquipmentWith remote temperature sensors Stand-alone thermostat mounting criteriaRemoving the Faceplate from the Base Pulling the front panel off of the baseDIP Switch Settings Setting the DIP SwitchReassembly Application SwitchAttaching the MiniVerter to the ViewStat Black to C Red to RWiring the VST-TSTAT to a VST-DIST Distribution Panel Inserting the MiniVerter into the mounting bracket top viewMounting the Base to a Wall CommunicationsPHASTLink RJ-45 Pinout Information EIA/TIA 568 a Connecting the ViewStat to AMX Control SystemsPin Wire Color Polarity Function NetLinx RJ-45 Pinout Information EIA/TIA 568 BGND Axcess System Card Edge PinoutsPin CTSTXD DB-9 Pinouts Wiring and Baud ConfigurationsRXD TX+DB-9 Pinouts Wiring and Baud Configurations Connecting to a NetLinx Master controller via NXC-COM card NXC-COM2 Pinouts NXC-COM2 Wiring ConfigurationConnecting to a NetLinx Control System Connecting to a LandMark Control SystemInstalling the Cat5 Suppression Ferrite RJ-45 Pinout InformationConnecting ViewStat to the Hvac System Installing the 24 VAC Suppression FerriteCommunication and Equipment Terminal Wiring Definitions Wiring the ThermostatCommunication and Equipment terminal wiring definitions Communication TerminalConnecting the ViewStat to the Hvac System DEH/Y1Red Black Power common From MiniVerter Check Out Procedure Checking Hvac System OperationOptional Hvac Set-Up Features To access these Hvac set-up featuresAddress the Thermostats and Set Highest Address Write down the address for each thermostat Wiring Diagrams Single-stage furnace and AC configurationTwo-stage furnace and two-stage AC configuration Two-stage furnace and two-stage AC configurationViewStat Installation and Wiring Boiler with AC two transformers configuration Boiler with AC two transformers configurationSingle-stage heat pump configuration Single-stage heat pump configurationTwo-stage heat pump configuration Two-stage heat pump configurationViewStat Installing the VST-TTM and VST-TRH Support Modules Single Support Module InstallationChoosing a mounting location Multiple Support Module Installation Removing the circuit boardSetting the Support Module DIP Switches Daisy-chaining support modulesDip switch 4 Humidity Sensor 2 VST-TRH support module only DIP switches 1 and 2 AddressDIP switch 3 Temperature Sensor DIP switch 6 T1/T2 or Onboard SensorApplications Heat Pump ApplicationsHumidity Control VST-TRH only Troubleshooting Remote Sensors Set Up and Configuration Network Override Set-Up Thermostat Button LockoutMaster key password is Security Set-UpCommunications Set-Up Temperature Set-UpTemperature Control Options Backlighting Set-UpBalance Point Options Balance Point Set-UpDisplay Set-Up Display Set-Up OptionsDisplay set-up AMXViewStat NetLinx Module Overview VST = VST1 = VST2 = Vstops =VSTZoneCnt Scale Dev VSTArry VST1 ViewStat Model Interface between the NetLinx program and the NetLinx moduleCommand Interface SENDCOMMANDs Command Interface SENDCOMMANDsCommand Description Tstat FMODE-val Stat FAN?FAN? Stat FMODE?Tstat HOLD-val Stat HMODE?HMODE? HOLD-ONTstat LOCK-val Tstat LIGHT-valLIGHT-T LOCK-ONOUTHUM? Tstat MSG-textTstat OUTHUM? Tstat OUTTEMP?String Feedback String FeedbackString Description HEAT-68 Stat FAN-valFAN-1 Tstat HUM-valTstat OUTHUM-val Stat ID-valStat MENU-val OUTHUM-68Stat TIME-val Tstat TEMP-valTEMP-76 MSG-2, Went shoppingPage Front Panel Components Mode buttonAdjust buttons Message DisplayMain display Fan buttonEnter button Main DisplayCool Selecting the ModeOperating The Thermostat HeatCase Of Power Failure Cleaning the ThermostatOperating the Thermostat ViewStat Communicating Thermostat It’s Your World Take Control

ViewStat specifications

AMX ViewStat is a revolutionary thermostat solution designed for both residential and commercial environments, providing robust control over heating, ventilation, and air conditioning (HVAC) systems. This intelligent device stands out for its user-friendly interface, advanced technology integration, and versatility in various settings.

One of the main features of AMX ViewStat is its intuitive touch screen interface, which enables users to easily navigate through settings and preferences. This 4.3-inch color display not only enhances usability but also allows for customization, offering users the ability to personalize the user experience according to their lifestyle and preferences. Whether adjusting temperature settings or scheduling heating/cooling cycles, the interface ensures a seamless interaction.

Among its key technological advancements is the integration of Wi-Fi connectivity. By connecting to a home or building's network, users can remotely access and control the thermostat through a smartphone, tablet, or computer. This level of control facilitates energy savings, as users can monitor and adjust settings from anywhere, leading to optimized usage and reduced utility bills.

AMX ViewStat is compatible with various HVAC systems, accommodating both conventional and heat pump setups. Its flexibility in adapting to different configurations makes it suitable for diverse applications, from single-family homes to large commercial spaces.

Moreover, the device incorporates advanced energy management features, granting users insights into their energy usage patterns. This data-driven approach allows users to make informed decisions about their energy consumption, ultimately promoting a more sustainable lifestyle.

In addition to its primary functions, AMX ViewStat integrates with other AMX control solutions, enabling a centralized command for home or office automation. When combined with AMX automation systems, users can achieve a fully integrated environment where lighting, security, and entertainment systems work in harmony with heating and cooling controls.

The construction of AMX ViewStat is robust yet stylish, designed to fit seamlessly into any decor. Available in multiple finishes, it adds a touch of elegance while ensuring durability and functionality.

In conclusion, AMX ViewStat is a state-of-the-art thermostat solution that offers a blend of advanced technology, ease of use, and energy efficiency. With features like remote connectivity, compatibility with various HVAC types, and integration with broader automation systems, it stands as a comprehensive solution for modern living and working environments.
Top Page Image Contents