AMX ViewStat manual Command Interface SENDCOMMANDs, Command Description

Page 53

Using the NetLinx Module to Program the ViewStat

cool setpoint would be set to 72. While the temperature is within this range nothing is done. Once the temperature falls outside this range the system takes action and switches to the appropriate mode.

5.Humidify/Dehumidify: Some systems can maintain the humidity level within a certain range. These are similar to temperature setpoints except instead of temperature control equipment the system is controlling humidify and dehumidify equipment.

Command Interface - SEND_COMMANDs

Various system wide operations may be performed by the NetLinx program via SEND_COMMANDs sent to the virtual device controlling the thermostats.

The supported commands are listed below.

Command Interface - SEND_COMMANDs

Command

Description

 

 

'T-<tstat> COOL-<val>'

Set cool set point.

 

Parameters:

 

• <tstat> : id of thermostat/zone

 

• <val>:

 

+ = increase cool set point by one degree

 

- = Decrease cool set point by one degree

 

60-108 = new cool set point (F)

 

Examples:

 

'T-4 COOL--'

 

'T-1 COOL-76'

 

 

'T-<stat> COOL?'

Query for current cool set point.

 

Parameter:

 

• <tstat>: id of thermostat/zone

 

Example:

 

'T-16 COOL?'

 

 

'T-<tstat> DATE-<val>'

Set date.

 

Parameters:

 

• <tstat> : id of thermostat/zone

 

• <val> : MMDDYY

 

Example:

 

'T-1 DATE-030894'

 

 

'T-<tstat> DATE?'

Requests current date on thermostat

 

 

'T-<tstat> DEHUMIDIFY-<val>'

Set dehumidify set point.

 

Parameters:

 

<tstat> : id of thermostat/zone

 

<val>:

 

+ = Increase dehumidify set point by one percent

 

- = Decrease dehumidify set point by one percent

 

10-90 = dehumidify set point (in percent)

 

Example:

 

'T-6 DEHUMIDIFY-70'

 

 

'T-<stat> DEHUMIDIFY?'

Query for current dehumidify set point.

 

Parameter:

 

• <tstat> : id of thermostat/zone

 

Example:

 

'T-1 DEHUMIDIFY?'

 

 

ViewStat Communicating Thermostat

47

 

 

Page 52 Page 54
Image 53
Page 52 Page 54
Contents ViewStat AMX Limited Warranty and Disclaimer Table of Contents Support Module Installation and Wiring Operating the Thermostat Table of Contents ViewStat Communicating Thermostat Introduction Product InformationViewStat Specifications ViewStat SpecificationsSystem Components System ComponentsCircuit Board Components Support Module SpecificationsEnclosure HWDMaximum Cable Distances VST-TTM and VST-TRH Remote Sensor SpecificationsMaximum Cable Distances Application # of Hvac Wiring Diagram Wires Hvac System Pre-Installation Check ListHvac System Pre-installation Check List Product Information ViewStat Communicating Thermostat With remote temperature sensors Disconnecting Power to All Hvac EquipmentSelecting the Thermostat Location Stand-alone thermostat mounting criteriaPulling the front panel off of the base Removing the Faceplate from the BaseReassembly Setting the DIP SwitchDIP Switch Settings Application SwitchBlack to C Red to R Attaching the MiniVerter to the ViewStatInserting the MiniVerter into the mounting bracket top view Wiring the VST-TSTAT to a VST-DIST Distribution PanelCommunications Mounting the Base to a WallPin Wire Color Polarity Function Connecting the ViewStat to AMX Control SystemsPHASTLink RJ-45 Pinout Information EIA/TIA 568 a NetLinx RJ-45 Pinout Information EIA/TIA 568 BPin Axcess System Card Edge PinoutsGND CTSRXD DB-9 Pinouts Wiring and Baud ConfigurationsTXD TX+DB-9 Pinouts Wiring and Baud Configurations NXC-COM2 Pinouts NXC-COM2 Wiring Configuration Connecting to a NetLinx Master controller via NXC-COM cardInstalling the Cat5 Suppression Ferrite Connecting to a LandMark Control SystemConnecting to a NetLinx Control System RJ-45 Pinout InformationInstalling the 24 VAC Suppression Ferrite Connecting ViewStat to the Hvac SystemCommunication and Equipment terminal wiring definitions Wiring the ThermostatCommunication and Equipment Terminal Wiring Definitions Communication TerminalDEH/Y1 Connecting the ViewStat to the Hvac SystemRed Black Power common From MiniVerter Checking Hvac System Operation Check Out ProcedureAddress the Thermostats and Set Highest Address Optional Hvac Set-Up FeaturesTo access these Hvac set-up features Write down the address for each thermostat Single-stage furnace and AC configuration Wiring DiagramsTwo-stage furnace and two-stage AC configuration Two-stage furnace and two-stage AC configurationViewStat Installation and Wiring Boiler with AC two transformers configuration Boiler with AC two transformers configurationSingle-stage heat pump configuration Single-stage heat pump configurationTwo-stage heat pump configuration Two-stage heat pump configurationViewStat Choosing a mounting location Installing the VST-TTM and VST-TRH Support ModulesSingle Support Module Installation Removing the circuit board Multiple Support Module InstallationDaisy-chaining support modules Setting the Support Module DIP SwitchesDIP switch 3 Temperature Sensor DIP switches 1 and 2 AddressDip switch 4 Humidity Sensor 2 VST-TRH support module only DIP switch 6 T1/T2 or Onboard SensorHumidity Control VST-TRH only ApplicationsHeat Pump Applications Troubleshooting Remote Sensors Set Up and Configuration Thermostat Button Lockout Network Override Set-UpSecurity Set-Up Master key password isTemperature Control Options Temperature Set-UpCommunications Set-Up Backlighting Set-UpDisplay Set-Up Balance Point Set-UpBalance Point Options Display Set-Up OptionsDisplay set-up VSTZoneCnt Scale Dev VSTArry VST1 AMXViewStat NetLinx Module OverviewVST = VST1 = VST2 = Vstops = Interface between the NetLinx program and the NetLinx module ViewStat ModelCommand Description Command Interface SENDCOMMANDsCommand Interface SENDCOMMANDs FAN? Stat FAN?Tstat FMODE-val Stat FMODE?HMODE? Stat HMODE?Tstat HOLD-val HOLD-ONLIGHT-T Tstat LIGHT-valTstat LOCK-val LOCK-ONTstat OUTHUM? Tstat MSG-textOUTHUM? Tstat OUTTEMP?String Description String FeedbackString Feedback FAN-1 Stat FAN-valHEAT-68 Tstat HUM-valStat MENU-val Stat ID-valTstat OUTHUM-val OUTHUM-68TEMP-76 Tstat TEMP-valStat TIME-val MSG-2, Went shoppingPage Adjust buttons Mode buttonFront Panel Components Message DisplayEnter button Fan buttonMain display Main DisplayOperating The Thermostat Selecting the ModeCool HeatCleaning the Thermostat Case Of Power FailureOperating the Thermostat ViewStat Communicating Thermostat It’s Your World Take Control

ViewStat specifications

AMX ViewStat is a revolutionary thermostat solution designed for both residential and commercial environments, providing robust control over heating, ventilation, and air conditioning (HVAC) systems. This intelligent device stands out for its user-friendly interface, advanced technology integration, and versatility in various settings.

One of the main features of AMX ViewStat is its intuitive touch screen interface, which enables users to easily navigate through settings and preferences. This 4.3-inch color display not only enhances usability but also allows for customization, offering users the ability to personalize the user experience according to their lifestyle and preferences. Whether adjusting temperature settings or scheduling heating/cooling cycles, the interface ensures a seamless interaction.

Among its key technological advancements is the integration of Wi-Fi connectivity. By connecting to a home or building's network, users can remotely access and control the thermostat through a smartphone, tablet, or computer. This level of control facilitates energy savings, as users can monitor and adjust settings from anywhere, leading to optimized usage and reduced utility bills.

AMX ViewStat is compatible with various HVAC systems, accommodating both conventional and heat pump setups. Its flexibility in adapting to different configurations makes it suitable for diverse applications, from single-family homes to large commercial spaces.

Moreover, the device incorporates advanced energy management features, granting users insights into their energy usage patterns. This data-driven approach allows users to make informed decisions about their energy consumption, ultimately promoting a more sustainable lifestyle.

In addition to its primary functions, AMX ViewStat integrates with other AMX control solutions, enabling a centralized command for home or office automation. When combined with AMX automation systems, users can achieve a fully integrated environment where lighting, security, and entertainment systems work in harmony with heating and cooling controls.

The construction of AMX ViewStat is robust yet stylish, designed to fit seamlessly into any decor. Available in multiple finishes, it adds a touch of elegance while ensuring durability and functionality.

In conclusion, AMX ViewStat is a state-of-the-art thermostat solution that offers a blend of advanced technology, ease of use, and energy efficiency. With features like remote connectivity, compatibility with various HVAC types, and integration with broader automation systems, it stands as a comprehensive solution for modern living and working environments.
Top Page Image Contents