Niles Audio PSW800 manual Existing Construction

Page 17

the drywall section can be replaced clean- ly if there is an unseen obstruction behind the wall. BE VERY CAREFUL NOT TO SAW THROUGH EXISTING WIRES, PIPES, OR STRUCTURE. IF YOU FEEL ANY EXTRA RESISTANCE AS YOU ARE CUT- TING, STOP.

4.If you are cutting into lath and plaster walls, use masking tape to outline your penciled marks, drill the four corners with a 1/4” bit and use a razor to score the

plaster down to the lath beneath. Then use a chisel to remove all of the plaster within the taped outline. Finally, insert a metal cutting blade into a sabre saw and very slowly and carefully saw the lath. Sawing the lath can easily vibrate plaster off the wall. If you have the patience, use a pair of tin snips to slowly nip away at the lath instead. There is no risk with this method, it is just time consuming.

Final Installation In New Or

Final Installation in New or Existing Construction

1.If it is possible to lay a batt of insulation into the wall cavity, do so. Remember to use equal amounts of insulation for each speaker. Install any other wall cavity improvements or modifications at this time.

2.Separate the speaker wire so that at least two inches of each conductor are free.

3.Strip one half inch of insulation from the end of each conductor of the speaker wire.

4.If you have gold pin connectors which you wish to use, affix them to the stripped wire ends now.

5.Connect one stripped wire end of the wire connected to the amplifiers right chan- nel output to the black and one to the red input terminals labeled for the right chan- nel. Pay attention to the markings on the wire. Repeat for the left channel.

6.Connect the wire which runs to the satellite speakers to the left and right output terminals. Pay attention to the markings on the wire.

7.Slip the mounting bracket through the hole and pull it toward you so that its front edge slides into the hole and stops in place.

8.Attach the frame to the bracket by screw- ing the frame to the bracket using the sup- plied screws. Do not overtighten the screws, this will distort the frame and the grilles will not fit (this is not permanent, just loosen the screws and the grille will pop in). The screws should pull the frame and bracket together (sandwiching the drywall) so that the frame is absolutely flush with the wall surface. There should be no gaps between the wall and the frame (See Figure 17).

9.Installing a Niles MS-1 MicroSensor™ There is a 1/2" round molded "IR Sensor Knockout" on the face of the speaker baf- fle. To prevent damage to the crossover network you must remove the knockout from the rear of the speaker. Do not attempt to remove the knockout with the speaker face up. Lay the speaker face down on a clean carpet or rug. Put the tip of a screwdriver into the center of the round "knockout" and sharply tap the screwdriver handle as necessary. Install the MS-1 using its mounting hex nut and washer so that it is tightly secured to the speaker. Connect all wires and continue your installation.

Existing Construction

16

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PSW800 Table of Contents Features and Benefits Easy Retrofit Installation in your Existing Home High Power HandlingInverted Dust Cap MicroPerf GrillesDual Subwoofer Systems Vlsa InstallationsSingle Stereo Subwoofer Connections Ciency. See Figure Speaker WireVery Large Subwoofer Array Vlsa With One or Two Subwoofers ImpedanceVlsa Four or More Subwoofers Check Your Amplifier’s SpecsSee Figure Using Speaker Selectors With Standard Volume ControlsMinimum Enclosure Size Speaker Placement TechniquesInsulation Enclosure BracingIntroduction Running the Speaker Wire in New ConstructionConcealing Speaker Wire in Existing Walls Location Installation Fundamentals Mounting The Model 800 New Construction Bracket ConstructionGrilles Existing Walls InstallationExisting Construction Painting the Speakers Speaker/Subwoofer PhaseSubwoofer Input Phase Reversal Cleaning Listening at Higher VolumesSatellite Left-Right Phase Reversal OperationModel PSW800 SpecificationsDetach Here WA R R a N T Y R E G I S T R AT I O N C a R D Niles Audio Corporation Limited WarrantyNiles Audio Corporation

PSW800 specifications

The Niles Audio PSW800 is a powerful subwoofer designed for home audio systems, delivering exceptional performance with an innovative blend of technology and engineering. Known for its deep, rich bass and high-efficiency output, the PSW800 is an ideal choice for audiophiles and casual listeners alike.

At the heart of the PSW800 is a high-quality 8-inch woofer, which utilizes a polypropylene cone that provides durability and reduces distortion. This driver is coupled with a robust magnet structure that enhances its performance, ensuring that the subwoofer can reproduce low frequencies with clarity and impact. With a frequency response range that extends down to 30 Hz, the PSW800 can produce the low-end sounds crucial for a full audio experience, whether it’s the thunderous explosions in an action movie or the intricate bass lines in music tracks.

One standout feature of the PSW800 is its built-in high-current amplifier. This powerful amplifier can deliver up to 200 watts of peak power, providing the necessary force to drive the woofer effectively. The combination of a dedicated amplifier with the woofer allows for a more cohesive and dynamic sound output, making it a valuable addition to any surround sound system.

The Niles Audio PSW800 also incorporates advanced room optimization technology. This system allows the subwoofer to adapt to various room acoustics by optimizing its performance based on the environment. This is particularly beneficial for users who may not have a dedicated home theater space and need a flexible solution to achieve the best sound quality.

Convenience features such as adjustable crossover frequency and volume controls offer users the ability to tailor the subwoofer's output to their specific listening preferences and room characteristics. Additionally, the PSW800 includes both line-level and speaker-level inputs, ensuring compatibility with a wide range of audio equipment.

The sleek design of the Niles Audio PSW800 ensures that it can blend seamlessly into any home decor while providing a solid and reliable performance. Its compact form factor makes it suitable for various living spaces without compromising sound quality.

In summary, the Niles Audio PSW800 stands out in the crowded subwoofer market, providing a combination of powerful bass performance, adaptive technology, and user-friendly features. For anyone looking to enhance their home audio experience, this subwoofer delivers exceptional value and performance.
Top Page Image Contents