Summary, Installation | Aube Technologies TH110-SP-P instruction

MODEL TH110-SP-P

SUMMARY

OPTIONS SELECTION

•To change the temperature from °C to °F and back, maintain D button pressed down as RESET button is being pressed on and released. Then release D button.

•To change the time format from 24 hours to 12 hours and back, maintain H button pressed down as RESET button is being pressed on and released. Then release H button.

TO SET TIME AND DAY

•Press on D, H and M buttons to adjust time and day.

TO RECORD THE HEATING PROGRAMS

•Set the operating mode to AUTO. Use the P button to select

the program to be recorded or modified. Once the program is selected, use H and M buttons to set time and or to select temperature setting.

TO RECORD THE ECONO PROGRAMS

•Set the operating mode to ECONO. Use the P button to select

the program to be recorded or modified. Once the program is selected, use D, H and M buttons to set time and day and or to select temperature setting.

OPERATING MODES

•To select an operating mode, use MODE button.

AUTO:

runs the programs.

shows temperature setting

MAN:

and can override temporarily your programming.

maintains the selected temperature.

changes

temperature setting.

ECONO:

maintains a temperature setting up to the user's

pre-programmed day and time.

shows

temperature setting.

INSTALLATION

NOTE: The "Problems and Solutions" section at the end of this user's guide will help you to correct your problems during the installation.

This thermostat has been designed to operate with any installation which has a RESISTIVE load not exceeding 4800 W (20 A) such as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is not compatible with a low voltage controller used by a central heating system.

Electricians or experienced technicians should install the thermostat.

This thermostat is designed to be used with a self-protected heating system equipped with thermal cut off and circuit breaker.

PARTS INCLUDED

-One (1) TH110-SP-P thermostat

-Two (2) 6-32 screws, 1 1/4 inches

-Three (3) solderless connectors

TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRIC SHOCK. Keep air vents of thermostat clean and free from obstructions.

1) Connecting wires and mounting thermostat

Connect the rear thermostat wires to the power supply and to the electric heater wires using solderless connectors for copper wires. See schematic diagram.

Push the excess wire back into the electric box to prevent interference with the thermostat. Secure the thermostat using two (2) 6-32 screws 1 1/4 inches long. Once the thermostat is properly installed, return power to heating system.

Note: All cables and connections must conform to the local electrical code.

WARNING: Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.

2) Options selection

Some options have been factory set. Those default settings are: The temperature is in °C and the time format is 24 hours.

2.1 Temperature displayed in °C or °F

To change the temperature from °C to °F and back, maintain D button pressed down as RESET button is being pressed on and released.

Then release D button.

2.2 Time format displayed in 24 hours or 12 hours

To change the time format from 24 hours to 12 hours and back, maintain H button pressed down as RESET button is being pressed on and released. Then release H button.

3) Memory backup

In the event of a power failure, an internal circuit will maintain the program- ming. An icon will be shown on the display. The display will stay on for 15 minutes; beyond this period, the display will turn off. Only the time will have to be set if power failure is more than six hours. The thermostat will return to the same operating mode as set before the power failure.

4) First power-up

When power is applied for the first time, the dis- play must show the day and hour as follows:

0:00 MO (Monday)

The active operation mode is the framed MAN mode, the temperature setpoint is 20 °C (68 °F) and the ambiant temperature is displayed.

If the display is different, maintain P button pressed down as RESET button is being pressed on and released. Then release P button.

OPERATING MODES

The thermostat displays the icon when the heating system is on and turns it off when the heating system is off.

The TH110-SP-P thermostat has three (3) operating modes:

AUTO, MAN and ECONO.

They are selected through the MODE button. On display, the active mode is framed. The frame moves on to the next mode each time the MODE button is pressed on.

The AUTOmatic mode runs in sequence (hourly) the programs recorded by the user.

By pressing once on or , the display shows the temperature setting. All subsequent pres- sures will override your programming up to the next program.

To see the weekday and weekend programs, select the AUTO mode and press successively on P button to see the programs appear on the display.

The MAN mode allows the user to override the programming.

The first time the or is pressed on, the temperature setting is displayed. For all subsequent times pressed on, the temperature setting will change 1 °C (1 °F).

720-110522-A 1/3

TH110-SP-P specifications

Aube Technologies has once again made waves in the HVAC industry with its innovative TH110-SP-P thermostat. Designed primarily for residential applications, this programmable thermostat combines advanced technology with user-friendly features to optimize energy efficiency and enhance home comfort.

One of the standout features of the TH110-SP-P is its 7-day programmable schedule. Homeowners can tailor heating and cooling settings to suit their weekly routines, allowing for maximum comfort when they are home and energy savings when they are away. The thermostat enables multiple program settings for each day of the week, ensuring that every family's unique lifestyle is accommodated.

In addition to its programmability, the TH110-SP-P boasts a clear, backlit display that makes it easy to read under any lighting conditions. Users can adjust temperature settings quickly and effortlessly, whether it’s in a peaceful early morning or a dimly lit evening. The intuitive interface eliminates the need for complex navigation, ensuring a seamless user experience.

The TH110-SP-P is compatible with a wide variety of heating systems, including electric baseboards, wall heaters, and many types of hydronic systems. This versatility makes it an ideal choice for various home heating setups, emphasizing Aube Technologies' commitment to providing solutions for diverse customer needs.

Moreover, the thermostat is engineered with advanced technology that promotes energy conservation. It features a temperature limit setting, preventing users from accidentally setting temperatures too high or low, which can lead to unnecessary energy consumption. This focus on energy efficiency not only conserves resources but also saves homeowners money on their utility bills.

Another notable characteristic is the built-in memory function. In the event of a power outage, the TH110-SP-P retains its settings, eliminating the need for reprogramming once power is restored. This feature ensures hassle-free operation and reliable performance over time.

Safety is also a priority in the design of the TH110-SP-P. It includes a limited heating tolerance function, which helps prevent overheating and ensures a secure operating environment.

Overall, the Aube Technologies TH110-SP-P thermostat is a perfect blend of advanced functionalities, ease of use, and energy-saving capabilities. With its programmable features and compatibility with various heating systems, this thermostat is a smart choice for homeowners looking to enhance comfort while managing energy consumption effectively.