Aube Technologies TH104 FI RST Power on, ADJ UST the TI ME and DAY, Opti on S Selection

Page 2

2) Secure the thermostat

Time display

 

 

Push the excess wire into

To change the time display format from 12 to

 

the electrical box to prevent

24 hours and vice-versa:

 

 

interference with the thermostat.

 

Press and hold

; do not release.

 

Secure the base to the electrical

 

 

 

Reset the thermostat using a pointed object

 

box using the provided screws.

 

TO RESET

 

(e.g. paperclip).

 

 

￿

 

THE

The base can be secured on the

 

Release the

button.

 

THERMOSTAT

left or right hand side of the electri-

 

 

 

 

 

cal box.

Temperature control type

 

3) Complete the installation

 

 

The TH104 is factory-set to use the proportional temperature con-

Once the thermostat is configured and installed, return power to

trol type (15-second cycles).

 

 

 

 

 

heating system.

 

 

 

Since this temperature control type uses a fast commutation rate, it

Keep the thermostat's air vents clean and free from obstructions.

is not compatible with fan-equipped systems. Also, it can also cause

light flickering, especially in rural regions.

 

 

 

 

 

FI RST POWER ON

 

 

If you have a fan-equipped system, use the conventional tempera-

 

 

ture control type (15-minute cycles). To change the type:

To

view the ambient

temperature,

 

 

Press and maintain

, do not release.

 

 

Reset the thermostat using a pointed object (e.g. paperclip).

peel the lower-right section of the

 

 

 

 

 

 

 

sticker and remove it from the display.

 

￿

Release the

button.

When you first power on the

 

Following the change, the FAN indicator is displayed on the screen.

thermostat, the display

 

 

 

To revert to proportional control, repeat above steps.

indicates: 0:00, MO (Monday),

the

 

 

 

 

 

ambient temperature and the MANual

 

 

ADJ UST THE TI ME AND DAY

mode is selected (framed). The

 

 

default setpoint is preset to 20°C.

 

 

 

 

 

 

Protected memory

 

 

 

NOTE: You should select the options before you adjust the clock

During a power failure, all programs are protected. The thermostat

and day settings because using the reset button when selecting

options will reset the clock.

 

display remains on for approximately 15 minutes after which the LP

 

 

 

 

 

indicator is displayed (low power). Only the time must be reset if the

The TIME icon flashes to indicate that the

power failure exceeds 6 hours. The thermostat will automatically

clock needs to be adjusted.

 

return to the previous mode when power returns.

 

! Press

to set the day.

 

 

 

 

 

OPTI ON S SELECTION

 

 

" Use the

and

buttons to

 

 

 

set the clock.

 

 

 

 

 

 

 

 

 

 

The TH104 offers the following options:

 

# Press

to exit.

 

 

 

 

 

 

Temperature display

 

°C

°F

 

OPERATI N G MODES

Time display

 

24 h

12 h

 

 

 

 

 

 

Temperature control

Proportional

Conventional

The TH104 has three operating modes:

Highlighted options are factory pre-set. If these options fit your

AUTOmatic

 

 

requirements, go to the next menu.

 

 

This mode automatically runs your programs.

 

 

 

 

 

Temperature display

 

 

 

Press MODE until AUTO is outlined. The current

 

 

 

 

 

To change the temperature display from °C to °F and vice-versa:

program number is displayed above the AUTO icon.

 

Press and hold

, do not release.

 

To temporarily bypass the current program, simply

 

 

select the desired temperature using the tempera-

 

Reset the thermostat using a pointed object (e.g. paperclip).

ture adjustment buttons. The new setpoint will be

 

maintained until the beginning of the next program.

 

Release the

button.

 

 

￿

 

 

MANual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maintains a constant temperature setpoint.

 

 

 

 

 

Press MODE until MAN is outlined and select the

 

 

 

 

 

desired temperature using the temperature adjust-

 

 

 

 

 

ment buttons.

 

 

2/4400-104-000-A

Image 2
Contents Nstallati on Connect the thermostatOpti on S Selection FI RST Power onADJ UST the TI ME and DAY Operati N G ModesAutomatic Schedule Using the Econo ModeProgramming the Econo Mode Econo ScheduleTechn I CAL Speci FI Cation S About Temperature CON TrolWarranty Techn I CAL SupportTH104-SW Procedure Locked Keyboard