Aube Technologies TH140-28 Basic Configuration, Select the Operating Mode, Program Your Schedule

1.5 Install the Batteries

When you first install the batteries, the unit runs a sequence of tests and a complete reset to zero. The

screen should display 0:00 MO and the ambient tem- perature. The current setpoint is 20°C.

The ambient temperature could be higher if you are holding the TH140 in your hands. It will return to normal about one hour after installation.

1.5.1 Replacing the batteries

The TH140 will display an icon indicating that the batteries must be replaced. This icon will be displayed for 60 days; after this delay, the TH140 will shut down the heating unit.

The time and programming are saved for 15 seconds when replacing the batteries.

oBasic Configuration

Note: You may program the thermostat while holding it in your hands or when it is mounted on the mounting plate.

2.1 Set the Time and Day

nSet the time, using the Hour and Minute buttons. o Set the day, using the Day button.

2.2 Configure the Setpoints

2.2.1 Comfort and Economy

These setpoints are associated to the schedule’s programs and are pre-programmed as follows:

Comfort	20°C (68°F)	Programs 1 and 3
Economy	18°C (64°F)	Programs 2 and 4

2.2.2 Vacation

This pre-programmed setpoint is used when the Vacation mode is activated.

Vacation 10°C (50°F)

2.2.3 To Modify a Setpoint

nSet the temperature using .

o Press and hold one of the setpoint buttons ( or or ) until the icon is displayed on the screen (approx. 3 seconds).

2.3 View the Current Setpoint

To view the current setpoint, quickly press

once one of the arrow buttons .

The screen displays the setpoint; the arrow indicates a setpoint.

pSelect the Operating Mode

The TH140 offers three operating modes:

3.1 Automatic

This mode executes the schedule. To activate:

• Press Manual/Auto until is displayed. The program setpoint icon is displayed.

3.1.1 Temporary Bypass

When in Automatic mode, you can temporarily bypass the

current program setpoint until the beginning of the next program. To bypass:

•Set the desired temperature OR quickly press or to use a pre-defined setpoint.

3.2 Manual

This mode allows you to maintain a constant temperature. To activate this mode:

• Press Manual/Auto until is displayed.

•Set temperature OR quickly press or to use a pre-defined setpoint.

3.3 Vacation

Maintains a specific temperature when away for a pro- longed absence (e.g. vacation).

• From the TH140, quickly press to activate.

•Can also be activated remotely (CT240, home automa- tion system or any other system) if the remote input is connected to one of these systems.

Note: When the Vacation mode is activated remotely, it can only be deactivated remotely.

Note: For details on how to activate the Vacation mode using a tele- phone, refer to the CT240 Instruction Manual.

qProgram Your Schedule

The TH140 allows four setting changes for each day of the week. There are no pre-set programs. Your heating system switches betw- wen the Comfort setpoint and the Economy setpoint according to the times you would have set.

For example, enter each day the time at which you wake up (PROG 1), the time you leave for work (PROG 2), the time you return home (PROG 3) and the time you go to bed (PROG 4):

Programs	Associated Setpoint	Time
PROG 1	(Comfort)	Wake-up
PROG 2	(Economy)	Leave
PROG 3	(Comfort)	Return
PROG 4	(Economy)	Sleep

Note: For temperature increases (PROG 1 and 3), allow at least 15 minutes per 1°C (2°F). For example, if you have lowered the temperature by 3°C (6°F) while you sleep and you wake up at 7 a.m., change the setting at 6:15 a.m.

TH140-28 400-140-000-C 2008-01-15 3/4