GE 19234 installation instructions Installation Instructions AC Wireless Chime Kit, Operation

GE Model 19234

www.jascoproducts.com

Wireless Door Chime Kit

Installation Instructions AC Wireless Chime Kit

Required Tools: Small flat blade screwdriver, drill, 1/16” drill bit, and phillips screwdriver.

Included Hardware:

(2) 3x20mm screws

(1) Double sided adhesive pad

The wireless door chime kit has two components:

The chime and pushbutton must be set to the same		Push Button Mounting Instructions	9.	Test operation. If the chime does not work, see
house security code for the combination to operate		Note: Avoid mounting on metal surfaces, as it may		TROUBLESHOOTING.
together.		result in a reduced range of transmission. Do not mount	If you do not want to drill holes in your door frame, you
1. Remove power from the chime.		in an area where exposed to direct rain.	can use the supplied double sided tape for installation.
		a. Removing the back cover	1.	Clean all mounting surfaces with a 50/50 mixture of
2. To remove the batteries from the pushbutton,			2.	isopropyl alcohol.
open the pushbutton case as shown below.				Remove the backing from one side of the double
				sided tape and press the exposed side against the
			3.	back plate of the push button.
				Remove the other backing strip and press the
				exposed side against the door frame where you want
				the button installed.
					Power Indicator
		b. Replacing the back cover
	Pushbutton
	House Code
	Jumpers

Chime (Receiver)	Battery Operated
	PushButton (Transmitter)
Plugs into 120V outlet	Battery included

Setting The House Security Code

Each chime component has 3 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code. If your chime activates intermittently or does not work at all, you may be able to solve the problem by changing your security code.

Pushbutton Jumpers

3.Locate the House Security Code door and screw located on the back of the Chime. Remove the screw and take off the door.

4.Locate the chime and pushbutton jumpers shown above.

5.To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. The jumpers on the chime and pushbutton must match exactly.

Wireless push button battery

To install or replace the battery in the wireless push button.

1. Remove the back cover of the push button.

Mounting Push Button

1. Push buttons are typically mounted at the same height as the door knob or handle (between 36” and 44” above the floor).

2. Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location.

Not further than 150 feet

3.Before placing the pushbutton where you would like to mount it, place the chime as close to final position as possible. Test the operation before drilling. If it works, mount the push button. If it does not work, see TROUBLESHOOTING.

4.Use back cover of push button as a template to mark two screw holes.

On/Off Switch

Operation

1.Plug the chime into a 120V AC outlet and slide the power switch to the “On” position to turn on the chime. The red LED power indicator will light.

2.Gently press transmitter button to sound chime.

Troubleshooting

Chime doesn’t work:

1. Make sure push button switch is depressed and held for at least 1 second.

2. Make sure house code switches 1-4 on chime and push button match exactly.

3. Verify battery orientation in push button.

4. Try fresh batteries.

5. Make sure chime is not farther than 150 feet away from push button.

6. Ensure push button is not mounted on metal, near metal studs, or near the floor.

7. Try a new location for the chime.

Functional range may be adversely affected by one or more of the following factors: weather, radio frequency interference, low transmitter battery and obstructions between the transmitter and receiver.

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept interference received, including any interference that may cause undesired operation.

2. Install the A23 (12 volt) battery with the negative side of the battery (-) toward the spring and the positive side of the battery (+) toward the positive battery holder as shown below.

Pushbutton

House Code Jumpers

3. Replace back cover as shown below.

19234-1.indd 1

4

5

6

8

5.Drill two holes with 1/16” size drill in marked locations.

6.Secure back cover to the mounting surface with two supplied mounting screws.

7.Install the supplied 12V battery observing proper polarity. (see battery installation section)

8.Press front housing onto back cover.

For technical support contact Jasco Products Company at 1-800-654-8483

or www.jascoproducts.com

Made in China/Hecho en China

is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114. www.jascoproducts.com

Rev. 04-10 19234

4/14/10 3:58 PM