Niles Audio SWA-500M manual Niles Audio Corporation 1-800-BUY-HIFI

Page 11

NOTE: FOR A HOME THEATER RECEIVER NOT EQUIPPED WITH A POWER TRIGGER OUTPUT, CONSIDER USING A NILES 12-VOLT POWER SUPPLY AS A TRIGGER SIGNAL THAT IS ACTIVATED VIA A SWITCHED AC OUTLET ON THE RECEIVER. SEE FIGURE 7 FOR CONNECTION DETAILS.

2.(Auto) POWER Switch: Use the ALWAYS ON mode to leave the SWA-500M always on. Use the MUSIC/VOLTAGE SENSE mode to automatically power on the SWA-500M when an audio signal or trigger voltage is present. When either signal is absent for 15 minutes, the SWA-500M will enter the standby mode.

NOTE: THE ALWAYS ON AND MUSIC/VOLTAGE SENSE SETTINGS ARE ONLY ACTIVE AFTER (MASTER) POWER IS SET TO ON.

3.MOVIE MODE TRIGGER: For external movie/music mode triggering, use a mini (3.5 mm) plug to connect the IN jack to a movie trigger signal from a home theater surround processor or receiver. The 3 to 30 Volts (AC or DC) signal will set the SWA-500M to movie mode, while a 0 Volts (AC or DC) signal will keep it in the music mode. Again, tip is positive. Use the OUT jack to pass the movie trigger signal to another

SWA-500M amplifier.

NOTE: IF THE SETUP SWITCH (SEE FIGURE 6 ON PAGE 7) ON THE FRONT PANEL IS SET TO MUSIC, A 3 TO 30 VOLTS (AC OR DC) TRIGGER SIGNAL WILL CHANGE OPERATION OVER TO THE MOVIE MODE. IF THE SETUP SWITCH IS ALREADY SET TO MOVIE, A TRIGGER SIGNAL HAS NO EFFECT, SINCE THE MODE IS ALREADY SET TO MOVIE.

4.SPEAKER switch: Use this switch to select the number of subwoofers (1 or 2) that are connected to the amplifier. Be sure that it is set to the correct position before turning on the amplifier or damage to the amplifier may result. If only one subwoofer is connected and the switch is set to the “Two sub” position, then no sound will be output from the amp.

5.BASS BOOST selector: Use this rotary switch during setup to select a frequency to enhance the sound of the subwoofer(s) connected. It should be set to the “-3dB down frequency” of the subwoofer.

6.AUDIO IN jacks: Use these gold-plated line-level RCA input jacks to connect line-level stereo or LFE audio signals from a home theater receiver or processor. The LFE (Low Frequency Effects) input is unfiltered by the SWA-500M.

7.AUDIO OUT jacks: Use these gold-plated line-level RCA output jacks to connect line-level stereo and LFE audio signals to drive another SWA-500M amplifier. The LFE output is unfiltered, but the L/R output signals are routed through the variable (60 to 160 Hz) HIGH-PASS filter, and the response will be contoured according to filter settings.

NILES AUDIO CORPORATION – 1-800-BUY-HIFI

 

9

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents SWA-500M Congratulations Table of ContentsIntroduction Niles SWA-500M high-power subwoofer amplifierImportant Safety Instructions Efficient Amplification Technology Flexible Installation & Multiple Bass CapabilityMaximum Subwoofer Performance Smooth and Accurate BassInstallation Considerations SWA-500M PlacementCleaning Rack Mounting the SWA-500M Connection to AUDIO/VIDEO Sources Loudspeaker WireConnecting the SWA-500M Controls and Connectors Running Wires in Walls or CeilingsIs indicated by the green LED on the front panel Signal Connectors and Power ControlsNiles Audio Corporation 1-800-BUY-HIFI Main power switch Applications SWA-500M in a Typical Home Theater InstallationSWA-500M and LINE-LEVEL Connection Connecting satellite loudspeakers Trigger connection Calibrating the SWA-500M Connecting the SWA-500MPage Checking Phase on the Satellite Loudspeakers Problem No sound Troubleshooting GuideSpecifications Limited Warranty Yes Warranty Registration CardL e s a u d i o C o r p o r a t i o n
Top Page Image Contents