Graco 308550ZAC important safety instructions Diaphragm Repair, Relieve the pressure

Page 19

Service

Diaphragm Repair

Tools Required

DTorque wrench

D13 mm socket wrench

DAdjustable wrench

D19 mm open–end wrench

DO-ring pick

DLithium-base grease

Disassembly

NOTE: A Fluid Section Repair Kit is available. Refer to page 27 to order the correct kit for your pump. Parts included in the kit are marked with an asterisk, for example (401*). Use all the parts in the kit for the best results.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 12.

1.Relieve the pressure.

2.Remove the manifolds and disassemble the ball check valves as explained on page 18.

3.Using 13 mm socket wrenches, remove the screws (107 and 108) holding the fluid covers

(101)to the air covers (23). Pull the fluid covers

(101)off the pump. See Fig. 12.

1You must torque the eight long screws (108) first, then the short screws (107). Torque to 190–220 in-lb (21–25 NSm).

See Torque Sequence, page 32.

2Arrow (A) must point toward air valve (B).

B

23

101

A 2

107 1

108 1

Fig. 12

04620B

308550 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Important Safety Instructions Instructions Parts ListModels Table of ContentsEquipment Misuse Hazard SymbolsToxic Fluid Hazard Toxic Fluid Hazard InstallationGeneral Information Tighten Screws Before First UseGround all of this equipment GroundingAir Line Typical FLOOR-MOUNT InstallationFluid Outlet Line Installation of Remote Pilot Air LinesMountings Fluid Suction LineBolt Tightening Sequence Flange ConnectionsFluid Pressure Relief Valve Changing the Orientation of the Fluid Inlet and Outlet PortsFire and Explosion Hazard Air Exhaust VentilationVenting Exhaust AIR Flush the Pump Before First Use Pressure Relief ProcedureStarting and Adjusting the Pump OperationMaintenance Problem Cause Solution TroubleshootingTroubleshooting Tools Required ServiceRepairing the Air Valve DisassemblyReassembly Relieve the pressure. Disconnect all hoses Ball Check Valve RepairDiaphragm Repair Reassembly Standard Diaphragms Reassembly Overmolded Diaphragms 105 19 402 24 104 403 Bearing and Air Gasket Removal Detail of Air Valve Bearings 308550 Husky 2150 Polypropylene and Pvdf Pumps, Series a Pump MatrixFor Husky 2150 Polypropylene and Pvdf Pumps, Series a Repair Kit MatrixParts Air Motor Parts List Matrix ColumnMuffler Fluid Section Parts List Matrix ColumnBall Parts List Matrix Column Seat Parts List Matrix ColumnDiaphragm Parts List Matrix Column 114 Torque Sequence Front View DimensionsSide View Pump Mounting Hole Pattern 14-0.8 MPa, 1.4-8 bar Technical DataFluid Flow GPM lpm Performance ChartFeet meters Psi MPa, barGraco Information Graco Warranties

308550ZAC specifications

The Graco 308550ZAC is a versatile and efficient airless paint sprayer designed for both DIY enthusiasts and professional contractors. Known for its reliability and performance, this unit provides consumers with a powerful solution for their painting projects, ensuring a smooth and even finish.

One of the standout features of the Graco 308550ZAC is its ProXChange technology. This innovative system allows for quick and easy pump replacement without the need for additional tools or complex procedures. This feature ensures minimal downtime, making it especially valuable on job sites where time efficiency is crucial.

The sprayer is also equipped with a powerful electric motor that delivers a consistent pressure of up to 3000 PSI. This high pressure not only facilitates a fine atomization of paint but also enables users to work with a variety of coatings, including thicker materials like latex, stains, and sealers. As a result, users can achieve professional-grade finishes on a range of surfaces, from buildings to fences.

Another significant characteristic of the Graco 308550ZAC is its adjustable pressure control. This feature allows operators to fine-tune the pressure according to the specific paint being used and the project's requirements. This flexibility translates to improved control over the spraying process, minimizing overspray and ensuring precision, particularly when working on detailed areas.

Additionally, the unit comes with a built-in suction hose, which can be submerged directly into paint containers for efficient and seamless painting. This capability makes it easier to use large buckets, reducing the hassle of constantly refilling the sprayer and enhancing productivity.

The Graco 308550ZAC also features a lightweight and portable design, making it easier to transport between job sites. Its robust construction ensures durability, while the ergonomic handle offers comfort during extended use.

In summary, the Graco 308550ZAC is a robust airless paint sprayer that combines advanced technologies and thoughtful design features to meet the needs of both professionals and hobbyists. With its ProXChange system, adjustable pressure control, and high-performance motor, it represents an excellent choice for achieving flawless finishes in various painting applications.
Top Page Image Contents