Graco 03761B Displacement Pump Service, Carbon Steel Displacement PUMPS, with rubber packings

Page 23

Displacement Pump Service

CARBON STEEL DISPLACEMENT PUMPS, with rubber packings

This procedure covers the following displacement pumps. Refer to the parts drawings on the indicated pages for an illustration of your pump.

DModel 218113, page 24.

DModel 218114, page 24.

DModel 218116, page 25.

Before You Start

1.Disconnect the displacement pump from the air motor as explained on page 11.

2.Be sure you have all the necessary repair parts on hand to reduce downtime.

3.Repair Kit 218112 is available. For best results, use all the new parts in the kit even if the old parts look good.

Intake Valve

1.Unscrew the intake valve housing (23) from the cylinder (13), using a strap wrench. Disassemble the valve and clean and inspect all parts.

2.Replace parts as necessary. Reassemble as shown in the applicable parts drawing.

Piston Valve

1.Using a strap wrench, grip the cylinder (13) near the outlet housing (6) and unscrew it from the housing. Pull the cylinder down off the piston. Check the inner surface of the cylinder for scoring or wear by running a finger over the surface or holding the part up to the light at an angle.

2.Loosen the lower nut (16) and unscrew the valve housing (18) from the connecting rod (17). Un- screw the piston stud (22).

3.Clean and inspect all piston parts. Replace parts as necessary. Reassemble the piston parts as shown, being sure that the lips of the u-cup pack- ing (21) are facing up. Screw the piston stud (22) into the valve housing (18) and torque to 31 NSm (24 ft–lb).

4.When reassembling the piston to the connecting rod (17), screw the connecting rod all the way into the displacement rod (15). Tighten the upper nut (16) against the displacement rod and torque to 33 NSm (24 ft–lb). Adjust the lower nut (16) to allow 3.1 mm (0.125 in.) free travel for the disk (19).

Throat Packings

1.Remove the cylinder (13) and piston as explained previously. Remove the packing nut (1) and pull the displacement rod (15) out of the top of the out- let housing (6). Inspect the outer surface of the displacement rod for scoring or wear by running a finger over the surface or holding it up to the light at an angle.

2.Remove the throat packings from the outlet hous- ing (6).

3.Clean and inspect the parts for wear or damage. Lubricate the packings before reassembly. Install the parts one at a time, in the same position as before. The lips of the u-cup must face down against fluid pressure.

4.Leave the packing nut (1) loose until the displace- ment rod (15) has been installed.

CAUTION

Insert the displacement rod from the top of the outlet housing to prevent shearing of the packings.

5.Tighten the packing nut just enough to prevent leaking. Overtightening can damage the packings.

6.Reconnect the displacement pump to the air motor as explained on page 11.

307427 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Table of Contents Instructions-Parts List307427 SymbolsFire and Explosion Hazard This model is Pump ModelsStubby Pumps Bung-Mounted Drum Length PumpsGrounding the System InstallationGeneral Information Model 226951 only Mounting the PumpModel 226951 Shown System AccessoriesModel 226951 Only All Other ModelsOperation Pressure Relief ProcedureFlush the Pump Before Using Starting and Adjusting the PumpMaintenance Problem Cause Solution TroubleshootingPressure Relief Procedure on Pump ServiceDisconnecting the Air Motor Reconnecting the Air MotorModel 226940 Shown Pump PartsBung Mount Drum-Length Pumps, Carbon Steel Models Description QtyModel 226953 Shown Bung Mount Drum-Length Pumps, Stainless Steel ModelsModel 226943 Shown Stubby Length Pumps Carbon Steel ModelsModel 226943, Series B, leather packed Model 226945 Shown Stubby Length Pumps Stainless Steel ModelsModel 226951, Series B, rubber packed Description Qty Bung Mount Adjustable Length Pump, Carbon Steel ModelPiston Valve Displacement Pump ServiceBefore You Start Intake ValveLiter 55 Gallon Size, Carbon Steel, Leather Packed Displacement Pump PartsModel 215953 Displacement Pump, Series D Model 215956 Displacement Pump, Series CStubby Size, Carbon Steel, Polyethylene Packed Model 215954 Displacement Pump, Series DModel 215957 Displacement Pump, Series C Liter 55 Gallon Size, Carbon Steel, Polyethylene PackedCylinder Model 237254 Displacement Pump, Series aLiter 55 Gallon Size, Carbon Steel, Ptfe Packed Model 237449 Displacement Pump, Series aStubby Size, Carbon Steel, Ptfe Packed Model 237255 Displacement Pump, Series aCarbon Steel Displacement PUMPS, with rubber packings Stubby Size, Carbon Steel, Rubber Packed Model 218113 Displacement Pump, Series aModel 218114 Displacement Pump, Series a Liter 55 Gallon Size, Carbon Steel, Rubber PackedAdjustable Length, Carbon Steel, Rubber Packed Model 218116 Displacement Pump, Series aDisplacement Pump Service Liter 55 Gallon Size, Stainless Steel, Polyethylene Packed Model 215955 Displacement Pump, Series BStubby Size, Stainless Steel, Polyethylene Packed Model 215958 Displacement Pump, Series B307427 Liter 55 Gallon Size, Stainless Steel, Ptfe Packed Model 237253 Displacement Pump, Series aStubby Size, Stainless Steel, Ptfe Packed Model 237256 Displacement Pump, Series aStainless Steel Displacement PUMPS, with rubber packings Liter 55 Gallon Size, Stainless Steel, Rubber Packed Model 220440 Displacement Pump, Series aStubby Size, Stainless Steel, Rubber Packed Model 220439 Displacement Pump, Series aBung Adapters AccessoriesWall Mounting Bracket Carbon Steel. See manual Open Tank Mounting ClampAir LIne Lubricator Ground Wire and ClampBleed-Type Master Air Valve Required Air LIne FilterPump No Overall Length Pump Length Fluid Inlet Fluid Outlet DimensionsCategory Data Technical Data307427 Graco Information Graco Standard Warranty

03761B specifications

The Graco 03761B is a high-performance airless paint sprayer designed to simplify the painting process for both homeowners and professionals. Renowned for its efficiency and ease of use, this sprayer is a go-to tool for delivering a smooth and even finish on a variety of surfaces.

One of the standout features of the Graco 03761B is its powerful motor. It is equipped with a robust electric motor that delivers consistent pressure, enabling the user to apply paint with precision. This feature allows for effective coverage, ensuring that every nook and cranny gets painted without any blotches or inconsistencies. The motor provides a flow rate of up to 0.34 gallons per minute, which translates to faster job completion, ultimately saving both time and effort.

The Graco 03761B utilizes advanced technologies such as the ProXChange Pump, which allows for fast and easy pump replacement on the job site. This innovation minimizes downtime, ensuring the project stays on schedule. Additionally, the airless jet technology allows users to apply coatings without the need for air compressors, reducing the equipment's weight and improving portability.

Another key characteristic of the 03761B is its adjustable pressure settings. Users can easily control the pressure to suit the type of paint and surface being sprayed. This flexibility provides the ability to tackle a wide range of applications, from fine detail work on furniture to large wall or fence projects.

The gun designed for this model is user-friendly, featuring a comfortable grip that reduces fatigue during prolonged use. The model also includes a reversible tip, which allows the user to quickly clear clogs without losing valuable work time.

The Graco 03761B is also designed with durability in mind. Its robust construction ensures that it can withstand the rigors of regular use, making it a reliable companion on job sites or during home improvement projects.

In summary, the Graco 03761B is a powerful, efficient, and versatile airless paint sprayer. With features like a strong motor, ProXChange pump system, adjustable pressure settings, and user-friendly design, it offers exceptional value for anyone looking to achieve a professional-quality finish with ease. Whether for a DIY enthusiast or a painting contractor, the Graco 03761B stands out as a top choice in the airless spray market.
Top Page Image Contents