Ingersoll-Rand AF0623SXXXXXX-XX-X specifications General Description, Trouble Shooting, Reassembly

Page 3

GENERAL DESCRIPTION

The chop-check pumps are primarily designed for the pumping of heavy viscous material with or without fibrous content. The models can be used with a gravity feed single post lift as a topper type assembly or with a two post lift as a force feed type assembly. The lower pump is designed for easy priming and the double acting feature is standard in all ARO industrial pumps. Material is delivered to the pump discharge outlet on both the up and down stroke.

The motor is connected to the lower pump end by a spacer section. This allows for lubrication of the upper packing gland and prevents motor contamination because of normal wear and eventual leak- age through the material packing gland. Be sure the solvent cup is adequately filled with lubricant to protect the upper packings and insure longest service life.

WARNING HAZARDOUS PRESSURE. Do not exceed maxi- mum operating pressure of 4215 p.s.i. (290.7 bar) at 150 p.s.i. (10.3 bar) inlet air pressure.

Pump Ratio X

=

Maximum Pump

Inlet Pressure to Pump Motor

 

Fluid Pressure

Pump ratio is an expression of the relationship between the pump motor area and the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is supplied to the motor of a 4:1 ratio pump, it will develop a maximum of 600 p.s.i. (41.4 bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate will increase as the motor cycle rate increases to keep up with the demand.

WARNING Refer to general information sheet for additional safety precautions and important information.

NOTICE: Thermal expansion can occur when the fluid in the mate-

rial lines is exposed to elevated temperatures. Example: Material lines located in a non-insulated roof area can warm due to sunlight. Install a pressure relief valve in the pumping system.

Replacement warning label (pn 92325) is available upon re- quest.

TROUBLE SHOOTING

Pump problems can occur in either the air motor section or the lower pump end section. Use these basic guidelines to help deter- mine which section is affected.

Pump will not cycle.

Be certain to first check for non-pump problems including kinked, restrictive or plugged inlet / outlet hose or dispensing device. Depressurize the pump system and clean out any ob- structions in the inlet / outlet material lines.

Refer to the motor manual for trouble shooting if the pump does not cycle and / or air leaks from the air motor.

Damaged motor. Service the motor.

Pump cycles but does not deliver material.

Refer to the lower pump end manual for further trouble shoot- ing.

PUMP CONNECTION - UPPER / LOWER

NOTE: All threads are right hand.

1.Lay the pump assembly on a work bench.

2.Remove the three (Y85-29-C) nuts from the three spacer rods (see figure 1).

3.Pull the air motor from the lower pump end until the motor piston rod is in the “down” position and the lower pump end rod is in the “up” position.

4.Using e-ring pliers, slide the retaining ring up far enough to allow the sleeve to move upward and release the two connec- tors (see figure 2). Lay the air motor aside.

5.Repeat step 4 to remove the other connector, then remove the extension rod.

6.Unscrew the three (92028) spacer rods only if disassembly of the lower pump end is necessary.

PUMP CONNECTION DETAIL

90163-8 Extension Rod

90102 Retaining Ring (2)

90109 Sleeve (2)

90096 Connector (4)

Lower Pump Piston Rod

Figure 2

REASSEMBLY

1.Align the pump motor and extension rod with the lower pump end. Position the air inlet of the motor 30° from the material outlet.

2.Install the two (90096) connectors and retain with the (90109) sleeve. Slide the (90102) retaining ring back into position.

3.Assemble the three (92028) spacer rods to the lower pump end and torque evenly to 60 - 90 ft lbs (81.3 - 122.0 Nm).

4.Bring the motor and lower pump together and retain with three (Y85-29-C) nuts.

AF0623SXXXXXX-XX-X (en)

Page of 4

Image 3
Contents Pump Performance Service KitsSpecifications Pump Data Model AF0623SXXXXXX-XX-XDimensions Pump Option Description ChartPump Connection Upper / Lower Trouble ShootingReassembly General Description83.3 166.6 250 Performance Curves

AF0623SXXXXXX-XX-X specifications

The Ingersoll-Rand AF0623SXXXXXX-XX-X is a cutting-edge air filter designed for industrial applications, known for its remarkable efficiency and durability. This model effectively addresses the needs of various sectors, including manufacturing, automotive, and food processing, where clean air is critical for optimal equipment performance and product quality.

One of the main features of the AF0623SXXXXXX-XX-X is its advanced filtration technology. The filter employs a multi-layer design that captures particles of varying sizes, from dust and dirt to oil mist and water droplets, ensuring that the compressed air entering machinery is pure and free from contaminants. This not only enhances the operational efficiency of air tools and pneumatic systems but also significantly extends the life of the equipment by reducing wear and tear.

Moreover, the AF0623SXXXXXX-XX-X boasts a high flow rate, allowing for seamless operation even in high-demand environments. Its robust construction is engineered to withstand extreme conditions, ensuring reliability even in harsh industrial settings. This model is also designed for easy installation and maintenance, minimizing downtime and operational disruptions.

Another significant characteristic of the Ingersoll-Rand AF0623SXXXXXX-XX-X is its low-pressure drop design. By maintaining optimal airflow while effectively filtering out unwanted particles, it contributes to energy savings, allowing facilities to operate more sustainably. This feature is particularly important in today's eco-conscious market, where businesses seek to reduce their environmental footprint while also managing operational costs.

The filter is compatible with a wide range of Ingersoll-Rand equipment, making it a versatile choice for various applications. It also meets stringent industry standards, ensuring that it can handle the demands of any commercial or industrial setting.

In summary, the Ingersoll-Rand AF0623SXXXXXX-XX-X air filter combines advanced filtration technology, high flow capacity, and enhanced durability to provide a reliable solution for maintaining clean air in industrial applications. Its design not only promotes the longevity of equipment but also facilitates energy efficiency, making it an essential component for any operation prioritizing performance and sustainability.