Electrolux F4VA1 manual Use of the control board, Programming section basic fea- tures

Page 11

F4VA1

Use of the control board

11

 

 

 

5.Use of the control board

The microprocessor programmer manages the pressing cycle in all of its functions. The user can pre-set 9 pressing programs.

The control panel is subdivided into 4 sections:

•PROGRAMMING: allows storage of 9 different work programs with programmable times and modes.

•EXCLUSION: allows partial or total exclusion of various press- ing functions.

•MODE: permits choice of various pressing cycle modes

•MANUAL CONTROLS: allows manual function of main press-

ing functions.

When the machine is switched on the control panel shows the last program used.

It is possible to adjust the brightness of the display: press

to

increase, press to decrease.

 

5.1.PROGRAMMING section - basic fea- tures

The programming section consists of:

•Program number display: from 1 to 9

•STEAM time display: from 00 to 99 seconds

•MIX / PAUSE time display. The two-figure display is shared by the two functions MIX (mixed steam + air) and PAUSE (pause between steam and blowing; used e.g. for touch ups)

•AIR time display: blowing time

•5 programming buttons.

To program a pressing cycle, do as follows:

1.Press the button PROG ( ) on the panel. A letter “P” ap- pears in the PROG display and the STEAM time display begins to flash.

1.

Press buttons

or

to increase or reduce the steam time.

2.Press the PROG. button ( ) to memorize the steam time.

3.The green light MIX and the display below begin to flash: press

or

to set a time of mixed steam + air after steaming, if

needed.

 

4.Press the PROG. button to memorize the mix time

5.The green light PAUSE and the display below begin to flash:

press or to set a pause time between steam and blowing, if needed (e.g. for touch ups with the iron)

6.Press the PROG. button to memorize the pause time.

7.

The AIR indicator starts to flash. Press

or

to set blowing

 

time.

 

 

8.Press the PROG. button. The display stops to flash. Program- ming is finished

If you need to change only one of the times, repeat all steps without modifying the other times.

Mix and Pause times can be used or not, depending on the needs. Table 5.1 shows the possible combinations.

5.2.PROGRAMMING section - advanced features

The PROGRAMMING sections allows adjustment of several param- eters. Refer to Table 5.2 for description of the parameters and their status. Figure 5.3 shows the look of the displays during programming of advanced parameters.

1.To access advanced programming press the PROG. button until the letter H appears in the program number display

2.The steam time display shows the number of the parameter under programming. Press PROG. to step forward to another parameter

3.The air time display shows a flashing number indicating the

parameter value. Press

or

to change parameter value

4.Press PROG. to memorize the value

Figure 5.3 - Displays during advanced parameters programming

5.Press PROG. several times, until the displays return to normal pressing times visualization.

The settings of the advanced parameters remain stored in the memo- ry associated to the program in which they were entered.

For example: if the machine is running program number 5 and the user enters advanced programming and excludes sleeve arms, the sleeve arms will remain excluded for future use of program number 5, even after switching off the machine.

5.3. Pressing cycle counter meters

The machine is equipped with two cycle counters:

•The total counter counts all the pressing cycles carried out by the machine in its work life and cannot be reset.

•The partial counter can be reset and can be utilized, for exam- ple, to count the number of garments processed in one day.

Partial counter meter

• To access the counters press push buttons and together for two seconds.

•The letter “C” appears on the PROG display. The other displays show the number of cycles.

•To reset the counter press “PROG”.

•

To exit meter mode, press

and

together till the displays

 

STEAM, MIX, PAUSE, AIR show pressing times.

Total counter meter

•

To access the counters press push buttons

and

together

 

for two seconds.

 

 

•The letter “C” appears on the PROG display. The other displays show the number of cycles.

•Press + to view the total cycles counter meter. The total cycles counter cannot be reset.

• To exit meter mode, press and together till the displays STEAM, MIX, PAUSE, AIR show pressing times.

The machine can work while the counter is visualized.

5.4. EXCLUSION section

This section consists of 4 buttons with red LED. The buttons allow exclusion of the following functions:

•rear clamp movement

•front clamp movement

•sleeve arms movement

•collar clamp movement

Pushing the button relative to the function effects exclusion. When the LED is on, the relative function is excluded.

Exclusions remain stored in the memory of the selected program. Excludes the rear clamp. When the light is on the clamp does not close. If the button is pushed during a cycle, the clamp opens but the cycle continues.

Excludes the front clamp. When the light is on the clamp does not close. If the button is pushed during a cycle, the clamp opens but the cycle continues.

Excludes the sleeve arms and cuff clamps. When the light is !2-3on the sleeve arms do not operate. If the button is pushed during a cycle, the cuff clamps open but the cycle continues.

Excludes the collar clamp. When the light is on the collar clamp #/,,!2 does not operate. If the button is pushed during a cycle, the #,!-0

collar clamp opens but the cycle continues.

F4VA1-ed3605

Page 10 Page 12
Image 11
Page 10 Page 12
Contents F4VA1 Shirt finisher Usage and MaintenanceF4VA1-ed3605 Index Residual risks Content and purpose of this manualSafety precautions IntroductionDescription of the machine How to identify the machineTechnical specifications Technical specificationsInstallation How to move the crated machine Use How to clamp the cuff Adjusting sleeve arms height Pressing cycle counter meters Programming section advanced featuresUse of the control board Programming section basic fea- turesButton Operating ModeManual Controls section Advanced programming parameters Setting mix and pause timesMaintenance allowed to the user MaintenanceControl board self-diagnosis TroubleshootingKnob 18 and gauge Both sleeve arms do Arms are excluded TroubleshootingDecommissioning Machine stopProlonged stop TransportationF4VA1 Electric Diagram Schema Elettrico Technical diagramsCuff clamp left Steam Cuff clamp right &YUSBF4VA1 Sleeve arms motion P8A Pneumatic Diagram Schema Pneumatico5200A35 Spare parts diagrams5200A06 Pedal Pedale5200A33 Carriage Assembly Gruppo Carro5200A5004 Pneumatic Adjustments Gruppo Regolazioni Pneumatiche5200A60 Control Panel Pannello DI Controllo5200A30 Front Clamp Assembly Gruppo Pala FrontaleStandard Size Form Gruppo Busto Uomo Side Clamps Group Gruppo Palette Laterali 5200A36L550 All models at 60Hz Motor Assembly 50Hz Gruppo Aria 50HzMotor Assembly 60Hz Gruppo Aria 60Hz All models at 50HzSteam Group Gruppo Vapore 5200A40Part All models at 60Hz 5200A61 Electric Panel 400V 50Hz Gruppo Elettrico 400V 50Hz5200A63 Electric Panel 60Hz Gruppo Elettrico 60Hz Part All models at 50HzValvola DI Ritegno L523 Spray Group option Gruppo Nebulizzatore opzionale L541 Electric Iron option Ferro Elettrico opzionale L522 Clamps Photocell option Fotocellula Pinze opzionaleValvola Ritegno Separatore Separateur Abscheider Separador Pneumatic Components Gruppo Pneumatico 5202A50Manual Sleeve Clamp Pinza Maniche Manuale 5200A34F4VA1 Spare parts F4VA1-ed3605 Dealer Manufacturer Document identification

F4VA1 specifications

The Electrolux F4VA1 is a cutting-edge vacuum cleaner designed to deliver exceptional cleaning performance while prioritizing user convenience and sustainability. This advanced appliance is engineered with several innovative features that make it a standout in the world of household cleaning.

One of the primary characteristics of the F4VA1 is its powerful suction capability. The vacuum is equipped with a high-performance motor that ensures efficient dirt and dust removal from various surfaces, including carpets, hardwood floors, and upholstery. This versatility makes it an ideal choice for multi-surface cleaning, allowing users to tackle a variety of messes with ease.

The F4VA1 also boasts an impressive filtration system. Utilizing a multi-stage HEPA filtration technology, it effectively captures allergens and fine dust particles, improving indoor air quality. This feature is particularly beneficial for households with pets or allergy sufferers, as it helps create a healthier living environment. The vacuum's dust container is designed for easy emptying, minimizing dust exposure during maintenance.

Comfort and convenience are at the forefront of the Electrolux F4VA1's design. It is equipped with an ergonomic handle and a lightweight structure, making it easy to maneuver around furniture and carry up and down stairs. The vacuum also features a range of attachments, including a crevice tool and a dusting brush, allowing users to clean hard-to-reach areas and delicate surfaces with precision.

The F4VA1 integrates smart technologies that enhance user experience. It employs a smart sensor system that adjusts suction power based on the surface being cleaned, optimizing energy efficiency without compromising performance. Additionally, the vacuum operates quietly, enabling users to clean at any time without disturbing household members.

Durability plays a crucial role in the Electrolux F4VA1's design. Constructed with high-quality materials, this vacuum is built to withstand regular use while maintaining peak performance. Backed by a reliable warranty, it assures users of its longevity.

In summary, the Electrolux F4VA1 stands out for its powerful suction, effective filtration system, user-friendly design, and smart technology integration. Ideal for various cleaning needs, it is a perfect companion for those seeking a reliable and efficient vacuum cleaner.
Top Page Image Contents