Testing Your Wood, First Fires, Ignition

Smaller pieces of wood will dry faster. All logs exceeding 6" in diameter should be split. The wood should not be stored directly on the ground. Air should circulate through the cord. A 24" to 48" air space should be left between each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be protected from the element but not the sides.

TESTING YOUR WOOD

When the stove is thoroughly warmed, place one piece of split wood (about five inches in diameter) parallel to the door on the bed of red embers.

Keep the air control fully open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your wood is damp.

If your wood hisses and water or vapour escapes at the ends of the piece, your wood is soaked or freshly cut. Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating potential conditions for a chimney fire.

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only burn small fires in your stove for the first four hours of operation. Never open the air control more than necessary to achieve a medium burn rate.

Make sure that there’s enough air circulation while curing the stove. The odours could be smelled during the 3 or 4 first fires. Never start your stove outside. You will not be able to see if you are over heating.

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper in the form of a tent. You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product should be used to light the fire.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.

We therefore advise you to leave the door slightly opened (1/4") for a 10 to 30 minutes period, under supervision, in order to allow for good combustion. After this time, you must close the door and progressively adjust the air control to obtain the desired temperature.

HT2000, HT1600, HT1200 specifications

The Drolet HT series represents a pinnacle of wood heating technology, showcasing the HT1200, HT1600, and HT2000 models. Each model is engineered with precise attention to detail, offering advanced features, superior efficiency, and robust performance that cater to diverse heating needs.

Starting with the HT1200, this model is ideal for smaller spaces or cozy cabins. It has a maximum heat output of 85,000 BTUs, making it effective for heating areas up to 1,200 square feet. Its firebox is designed for optimal airflow, ensuring complete combustion and minimal emissions. It features a large glass door, allowing for an enchanting view of the flames while improving heat output through radiant warmth. The HT1200 is equipped with a secondary combustion system that enhances efficiency and reduces smoke, exemplifying eco-friendly heating solutions.

Stepping up, the HT1600 is tailored for medium-sized homes, delivering a remarkable maximum heat output of 100,000 BTUs, suitable for spaces up to 1,600 square feet. The HT1600 boasts an impressive 22-inch log capacity, which means less frequent reloading and more sustained warmth. This model also incorporates an advanced air wash system that keeps the glass door clean, ensuring an unobstructed view of the fire while maintaining efficiency. The construction of the HT1600 includes heavy-duty steel and firebricks, which help retain heat long after the fire has died down, thus providing extended warmth.

The flagship of the series, the HT2000, is designed for larger homes or open-concept spaces, offering a powerful heat output of 150,000 BTUs, sufficient for spaces exceeding 2,000 square feet. The HT2000 emphasizes maximum efficiency with an exceptional thermal efficiency rating, allowing homeowners to save on fuel costs while enjoying consistent warmth. Its broader firebox can accommodate larger logs, lengthening burn times and enhancing overall heating performance. Furthermore, the unit’s state-of-the-art internal baffle system promotes optimal gasification, ensuring complete combustion and reduced emissions.

All models in the Drolet HT series are EPA certified, underscoring their commitment to environmental responsibility. Built with rugged materials and engineered for longevity, these stoves are designed to withstand the rigors of daily use. With customizable aesthetic options and a focus on user-friendly operation, the Drolet HT1200, HT1600, and HT2000 combine traditional craftsmanship with modern technology, offering reliable and efficient wood heating solutions for every home.