England's Stove Works 50SVL17, 50TVL17, 17VL manual Creosote Formation and Need for Removal

Page 18

OPERATION

•England’s Stove Works, Inc. always recommends the use of a magnetic stove thermometer, so that the temperature of the unit can be monitored. When using a magnetic stove thermometer, locate the thermometer above the door on either the left or right side of the stove and use the following temperatures as rough guidelines to determine the burn rate and heat output level of the stove:

o Normal wood stove operation should occur between 350°F (177°C) and 550°F (288°C), with 350°F (177°C) to 450°F (232°C) being a low to medium heat output level and 450°F (232°C) to 550°F (288°C) being a medium to high heat output level. Operating the stove at 600°F (316°C) would be considered the maximum continuous operating temperature permissible and unit damage may result from operating at that high of a burn rate for extended time periods. Allowing the unit to reach 650°F (343°C) or higher is defined as over‐firing and will result in unit damage.

•The optional room air convection blower was designed to extract the maximum amount of heat from the stove, for the highest possible heat transfer into the room. Since the blower is so efficient at removing heat from the unit, it is very important to only operate the room air blower after a fresh wood load has been allowed to burn for at least thirty (30) minutes. Allowing a fresh load of wood to burn without the blower on ensures that the entire unit reaches proper operation temperatures and that the secondary combustion system is functioning properly. Additionally, follow the guidelines below for acceptable blower speeds.

•When using the optional room air convection blower (Part No. AC‐16), the blower should be operated as follows depending on heat output level:

Burn rate

High

Medium High

Medium

Medium Low

Low

Blower Speed

High

Low

Low

Low

Off

Creosote – Formation and Need for Removal

When wood is burned slowly, it produces tar and other organic vapors, which

combine with expelled moisture to form creosote. The creosote vapors

condense in the relatively cool chimney flue of a slow‐burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire. The chimney and chimney connector should be inspected at least once every two months during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated, it should be removed to reduce the risk of chimney fire.

DO NOT USE GRATE OR ELEVATE FIRE – BUILD WOOD FIRE DIRECTLY ON HEARTH

DO NOT OPERATE WITH THE MAIN DOOR OPEN – OPERATING THE STOVE WITH THE MAIN

DOOR OPEN WILL CREATE AN OVER‐FIRE

Page 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Tranquility Wood Stove Retain for your files Table of Contents Introduction Specifications Heating SpecificationsInstallation Clearances to Combustibles Installation Flue Gas Direction Wall Pass‐Throughs Installation Approved Venting Method 2 Through the Ceiling 10 ft Ft .0 ft 18.0 Installation Floor Protection Value Calculation Operation Creosote Formation and Need for Removal Operation Maintenance Maintenance Replacing Components Troubleshooting Issue Cause SolutionsReplacement Parts List Illustrated Parts Diagram Page Limited Five 5 Year Warranty Warranty is not transferable Warranty Registration for England’s Stove Works Important Notice

50SVL17, 17VL, 50TVL17 specifications

England's Stove Works is renowned for manufacturing high-quality wood and pellet stoves, and their models 50TVL17, 17VL, and 50SVL17 are excellent representations of their commitment to efficiency, functionality, and design. These stoves are designed to meet various heating needs while promoting sustainability and comfort.

The 50TVL17 is a versatile pellet stove that boasts a powerful yet efficient heating capability. With an impressive 50,000 BTU output, this model can heat spaces up to 2,200 square feet, making it ideal for both large and small homes. One of its standout features is the large hopper capacity, allowing for extended burn times without the need for frequent refueling. Additionally, the 50TVL17 comes with an automatic ignition system that ensures quick and reliable starts, enhancing user convenience.

The 17VL, on the other hand, is known for its compact design and high efficiency, capable of heating areas up to 1,500 square feet. This stove operates with a maximum output of 30,000 BTU, making it suitable for standard-sized rooms. It features a simple and efficient feed system, which not only promotes consistent heat output but also reduces pellet consumption. The 17VL is equipped with a programmable thermostat for precise temperature control, allowing users to set their desired warmth and leave the rest to the stove.

The 50SVL17 is another stellar offering, combining the benefits of both wood and pellet heating. This multi-fuel stove boasts a stunning design that can complement various home decors while providing effective heating solutions. With a robust construction and a 50,000 BTU capacity, it can also heat larger spaces, featuring an adjustable blower for optimal heat distribution. The 50SVL17 focuses on minimizing emissions, leveraging advanced combustion technologies that meet and often exceed environmental regulations.

Each of these models incorporates user-friendly features like easy-to-clean designs and large viewing windows that showcase the beautifully burning flames. England's Stove Works has also ensured that safety is paramount, with built-in overheat protection and exhaust safety features.

Overall, the 50TVL17, 17VL, and 50SVL17 from England's Stove Works stand out not only for their impressive heating performance but also for their thoughtful design and eco-compatible technologies. These models are perfect for anyone seeking an efficient and stylish way to heat their spaces while being mindful of their environmental impact.
Top Page Image Contents