Draper 1000 owner manual Reloading, Creosote Formation and Need for Removal

Page 17

WARNINGS

•NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER SETTING.

•THE INSTALLATION OF A LOG CRADLE IS NOT RECOMMENDED IN YOUR DROLET WOOD STOVE.

•NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX.

Use the following table to adjust the draft control to the desired burn rate:

 

 

BURN RATE

DRAFT SETTING

Low and Medium Low

Push control to the left.

Medium

Push control 3/16" to the right

Medium High

Push control over by approx.

 

3/16" to 5/16" from low setting

High

Push control all the way over.

 

 

Closing the draft control down too soon will hurt combustion efficiency and result in creosote build-up in the chimney (which could lead to a chimney fire some time in the future).

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air controls to maximum a few seconds prior to opening the stove's door. Then proceed by opening the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draught and thus eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you operate it with a wood load approximately equivalent to the height of fire bricks.

It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall. Refer to page 16 of the present manual.

CREOSOTE FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire. When burning wood, the chimney connector and chimney should be inspected at least once every two months during the heating season to determine if a creosote build-up has occurred.

16

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Read and Keep this Manual for Reference OWNER`S Manual 1000 Model StoveTable of Contents Introduction 000 41,000 BTU/HR Technical SpecificationsBenefits of Installing a Blower Door AdjustmentPositioning the Stove InstallationClearances from Combustibles Floor ProtectorReduced Clearances Type of Protection Chimney Chimney Connector Stove Pipe Factory Built Chimney Typical InstallationsFactory Built Thimble Brick Thimble Average Energy Yield of ONE AIR Dried Cord of CUT Wood Woodstove UtilisationOutside Combustion AIR Wood species Energy yield Millions of BTU/cord Testing Your WoodHeating First FiresIgnition Creosote Formation and Need for Removal ReloadingTo Prevent Creosote Build UP MaintenanceASH Disposal GlassGasketing Gold Door CleaningBrick Layout PaintSymptom Possible Cause Corrective Action Smoke in room TroubleshootingDescription Limited Lifetime Warranty

1000 specifications

The Draper 1000 is a state-of-the-art projection screen designed for commercial and residential use, offering a premium viewing experience. It is particularly renowned for its versatility and exceptional performance in various environments, including conference rooms, classrooms, and home theaters.

One of the standout features of the Draper 1000 is its robust construction. The screen is built with a sturdy aluminum housing that ensures durability and longevity, making it suitable for frequent use. This durability is complemented by a sleek design that allows the screen to blend seamlessly into any decor.

The Draper 1000 utilizes advanced projection technologies, allowing it to deliver crystal-clear images and vibrant colors. The screen is compatible with various projection systems, such as front and rear projectors, making it a flexible choice for different setups. Its surface is designed for optimal light reflection, ensuring that images are bright and easily visible in different lighting conditions.

Another significant characteristic of the Draper 1000 is its easy installation process. The screen comes with a range of mounting options, including wall brackets and ceiling kits, providing users with flexibility in placement. This adaptability makes it suitable for both permanent installations and mobile setups.

In terms of size, the Draper 1000 is available in various dimensions, accommodating different viewing distances and room sizes. This customization ensures that users can select the ideal screen size for their specific needs, whether it is for a small meeting room or a large auditorium.

The screen also incorporates advanced motorization options. The electric version of the Draper 1000 features a quiet, reliable motor that allows for smooth and effortless retraction and deployment. This motorized functionality enhances convenience, making it easier to set up and pack down the screen as needed.

Additionally, the Draper 1000 offers customizable screen surfaces, which can be selected based on the specific type of projection needed. Whether it’s a matte white surface for excellent color accuracy or a high-gain option for environments with high ambient light, users can choose the surface that best suits their requirements.

In conclusion, the Draper 1000 stands out as an exceptional projection screen due to its rugged design, advanced projection capabilities, flexibility in installation, and variety of sizes and surfaces. This makes it an ideal choice for anyone looking to create an immersive viewing experience in various settings.
Top Page Image Contents