Enviro C-10629 owner manual Operating Instructions, Efficiency

Page 7

Operating Instructions

CONTROL BOARD FUNCTIONS:

1.AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to 2.5 seconds ON time Auger pulse. This is done only on LOW to allow the burning of poor quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On time to 1.5 second. This setting is for high-grade fuel only. Push the button until just the number 1 light is on, this is for a 2 second ON time (standard setting). Refer to Figure 3.

2.CONVECTION BLOWER CONTROL: Used to turn the convection blower ON/OFF. If the Blower is left off, and the sensor located on the air jacket reaches 160 °F (71 °C), the Convection blower will automatically come on HI speed to cool the unit. Leave the convection blower ON for peak

 

efficiency

 

AUGER TRIM

 

�

�

�

 

 

FAN

 

�

 

�

 

MANUAL FEED

 

�

 

ON/OFF

�

�

 

HEAT LEVEL

Figure 2: Circuit Board Control Panel Decal

3.AUGER PULSE LIGHT: This light will flash in conjunction with the auger.

4.MANUAL AUGER FEED: If the unit runs out of fuel, this button can be used to “prime the auger system”. This button will turn off after 60 seconds and then must be released and pressed again.

5.SYSTEM LIGHT: Responsible for signaling the state of the control board. When the light is flashing during start-up, the stove is in an automatic start mode. When the light is solid, the Heat Level Setting can be altered.

6.ON/OFF BUTTON: Used to turn the unit ON and OFF.

7.HEAT OUTPUT INDICATOR: Shows the present heat output setting.

8.HEAT LEVEL ADJUSTMENT: When pressed, will change the heat setting of the unit from low to high in five (5) steps.

Auger Trim

Auger Trim

Auger Trim

4 1.5 Seconds "ON"

5

2 Seconds

 

2.5 Seconds

"ON"

 

"ON"

Factory Setting

 

 

 

1

1

1

 

Figure 3: Auger trim

and heat level indicator.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Bern Table of Contents Introduction Reasons WHY the Unit OverheatedStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Rating label is located on the inside of the ash pan cover Efficiency Operating InstructionsInitial START-UP See above Thermostat / Switch ModeSlider/Damper Plate in Unit Special NotesTools Required to Clean Unit Routine Cleaning and MaintenanceNot Place Unburned or RAW Pellet Fuel in ASH PAN ASH PAN weeklyExhaust Passages semi-annually Blower Mechanisms season Post Season CLEAN-UPDoor Glass Replacement Exhaust Vent annuallyTo the Distributor WarrantyFor the do-it-yourself Individual Name of Owner Address Installation Data Sheet

C-10629 specifications

Enviro C-10629 is an innovative product designed for effective environmental management and sustainability solutions. This versatile formulation is particularly well-regarded for its ability to combat a wide range of environmental challenges, making it an essential tool for various industries, including agriculture, waste management, and soil remediation.

One of the main features of Enviro C-10629 is its biodegradable nature, which aligns with modern ecological practices. This characteristic not only helps minimize environmental impact but also ensures that the product can be safely used in sensitive ecosystems without leaving harmful residues. The formulation is designed to break down into non-toxic by-products, thereby contributing to a circular economy.

The technology behind Enviro C-10629 is based on advanced microbial and enzymatic activity. This allows the product to work in synergy with the natural processes found in soil and water environments. By harnessing the power of beneficial microorganisms, Enviro C-10629 enhances nutrient availability and improves soil health, facilitating robust plant growth and crop yields.

In terms of characteristics, Enviro C-10629 exhibits excellent compatibility with other agricultural inputs, which allows it to be easily integrated into existing practices. This compatibility ensures that farmers and land managers can use it in conjunction with fertilizers and other soil amendments without any adverse reactions. As a result, individuals can maximize the effectiveness of their agricultural inputs while promoting environmental sustainability.

Furthermore, Enviro C-10629 is designed to be user-friendly and requires minimal application effort. With an effective delivery system, it can be applied through various methods, including spraying, drenching, or mixing with irrigation systems. This ease of use ensures that users can implement the product without extensive training or specialized equipment.

Overall, Enviro C-10629 stands out as a cutting-edge solution for environmental challenges. Its biodegradable composition, advanced microbial technology, compatibility with other agricultural practices, and user-friendly application methods make it an essential product for those seeking to promote sustainability while maintaining productivity. As industries increasingly prioritize eco-friendly solutions, Enviro C-10629 represents a significant step forward in achieving these goals.
Top Page Image Contents