USE of Cordwood is Prohibited by LAW

Introduction

IMPORTANT SAFETY DATA:

Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area.

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions.

Be sure to maintain the structural integrity of the home when passing a vent through walls, ceilings, or roofs.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash pan and viewing door must be locked securely for proper and safe operation of the pellet stove.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by adjusting the slider damper located on the left side of the stove.

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all construction meets local building codes.

Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an extremely rich burn (black tipped, lazy orange flames).

If you have any questions with regard to your stove or the above-mentioned information, please feel free to contact your local dealer for further clarification and comments.

SAFETY WARNINGS AND RECOMMENDATIONS:

Caution: Do not connect to any air distribution duct or system.

Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil. Unit hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

FUEL: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash content. Dirty fuel will adversely affect the operation and performance of the unit and may void the warranty. Check with your dealer for fuel recommendations.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See: “SLIDER/DAMPER SETTING”.

CLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This will vary due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect and clean the exhaust vent semi-annually or every two tons of pellets.

ASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container

Mini A specifications

The Enviro Mini A is a compact and efficient solution designed for a variety of environmental monitoring applications. As the demand for sustainable practices increases, the Enviro Mini A emerges as a key player in facilitating real-time data collection and analysis of environmental parameters.

One of the main features of the Enviro Mini A is its advanced sensor technology. It is equipped with high-precision sensors that can monitor various environmental factors, including air quality, temperature, humidity, and atmospheric pressure. These sensors are designed to provide accurate readings, allowing users to make informed decisions based on reliable data.

The design of the Enviro Mini A is another significant characteristic that sets it apart. Its compact size allows for easy installation in a variety of locations, from urban settings to remote areas. This versatility makes it suitable for deployments in schools, parks, industrial sites, and research facilities. The device can be mounted on poles, walls, or placed on flat surfaces, ensuring flexibility in how it can be utilized.

Connectivity is a critical aspect of the Enviro Mini A's functionality. The device is equipped with Wi-Fi and optional cellular connectivity, enabling seamless data transmission to cloud-based platforms for real-time analysis and monitoring. Users can access the data remotely via a user-friendly interface, allowing for quick responses to any environmental changes or alerts.

The Enviro Mini A also boasts a robust and weather-resistant design, making it capable of withstanding various environmental conditions. This durability ensures longevity and reliability, even in challenging outdoor settings. Furthermore, the device is energy-efficient, often powered by solar energy or a long-lasting battery, which reduces maintenance efforts and operational costs.

Incorporating advanced data analytics capabilities, the Enviro Mini A allows users to track trends over time, identify patterns, and generate reports that can assist in regulatory compliance and environmental assessments. Its integration with machine learning algorithms aids in predictive analytics, offering insights that can drive proactive environmental management strategies.

In summary, the Enviro Mini A is a state-of-the-art environmental monitoring device that combines advanced sensor technology with a robust design and connectivity features. Its versatility and analytical capabilities make it an invaluable tool for anyone looking to monitor and improve environmental conditions effectively.