Enviro C-10984 owner manual ASH PAN weekly, Not Place Unburned or RAW Pellet Fuel in ASH PAN

Page 11

Routine Cleaning and Maintenance

If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may be purchased through most dealers. If a gas appliance glass cleaner is not available, use a damp paper towel dipped in fly ash to clean the glass. After the glass has been cleaned use the dry soft cloth to wiping down the outside and inside of the glass.

ASH PAN (weekly)

This part is located under the door. To remove the ash pan, open the cover from the right hand side, and lift the ash pan up and out. Dump the ashes into a metal container stored away from combustibles. Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good indication of fuel efficiency and quality. Refer

to “SAFETY WARNINGS AND RECOMMENDATIONS” for

disposal of ashes. Vacuum the inside of the ash pan compartment inside the pedestal including the hole at the top back of the compartment. Replace the ash pan and close pedestal door. DO

NOT PLACE UNBURNED OR RAW PELLET FUEL IN ASH PAN.

AIR INTAKE (semi-annually)

Inspect periodically to be sure that it is not clogged with any foreign materials.

EXHAUST PASSAGES (semi-annually)

Heat exchanger tubes

cleaner handle.

Vacuum the top &

bottom air wash.

Burn pot

clean-out lever.

Empty ash box.

Vacuum inside ash

box compartment.

Figure 6: Bern Open

To prevent build up of fly-ash all the exhaust passages must be cleaned and vacuumed.

Clean behind clean-out covers:

•Open ash box cover.

•Remove ash box.

•Using a 5/16” socket, loosen the six (6) screws in the ash box compartment; four (4) on the back and one (1) on each side (see Figure 7).

•Rotate the back cover counter- clockwise to remove and rotate the side covers to open them.

•Vacuum out all three (3) chambers.

•Close all the clean-out covers and tighten the screws.

Loosen the screw & rotate the cover (left & right sides)

Loosen the four (4) screws, rotate counter-clockwise & remove.

Figure 7: Bern Clean-Out Covers.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Mini Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionI. Pellet Standards USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Rating label is located on the back of the unit Dimensions of BernHeat Output Reasons WHY the Unit OverheatedHeat Level Adjustment Operating InstructionsInitial START-UP See above Thermostat / Switch ModeSlider/Damper Plate in Unit Special NotesTools Required to Clean Unit Routine Cleaning and MaintenanceExhaust Passages semi-annually ASH PAN weeklyNot Place Unburned or RAW Pellet Fuel in ASH PAN Blower Mechanisms season Post Season CLEAN-UPDoor Glass Replacement Exhaust Vent annuallyFor the do-it-yourself Individual WarrantyTo the Distributor Name of Owner Address Installation Data Sheet

C-10984 specifications

Enviro C-10984 is a cutting-edge environmental technology designed to address a myriad of ecological concerns while promoting sustainability. Launched as a part of an initiative to enhance waste management practices, C-10984 integrates state-of-the-art features and technologies to maximize efficiency and minimize environmental impact.

At the core of Enviro C-10984 is its advanced waste processing system. This system utilizes a combination of mechanical, biological, and thermal methods to reduce waste volume and convert it into reusable resources. The waste-to-energy technology embedded within the C-10984 allows for the transformation of organic waste into biogas, which can then be harnessed for energy generation, significantly decreasing reliance on fossil fuels.

One of the standout characteristics of Enviro C-10984 is its commitment to resource recovery. The system is equipped with a sophisticated sorting mechanism that effectively categorizes waste into recyclable, compostable, and non-recyclable materials. This capability not only streamlines the waste management process but also increases the efficiency of recycling programs, subsequently reducing landfill accumulation.

Another innovative feature of the C-10984 is its real-time monitoring system. Utilizing IoT technology, the device can track waste volume, energy production, and resource recovery metrics. This data-driven approach allows for improved decision-making, enabling municipalities and organizations to optimize their waste management strategies.

The design of Enviro C-10984 emphasizes ease of use and adaptability. The modular architecture enables it to be tailored to different scales, from small communities to large urban centers, ensuring that diverse needs are met. In addition, the system operates quietly and efficiently, adhering to strict regulatory standards while minimizing disruption to surrounding areas.

Lastly, Enviro C-10984 prioritizes user engagement through a dedicated mobile application. This app allows users to monitor their waste production, access educational resources, and receive customized recommendations for reducing waste, thereby fostering a culture of sustainability within users’ communities.

In summary, Enviro C-10984 represents a significant advancement in environmental technology. With its innovative features, commitment to resource recovery, real-time monitoring, and user-friendly design, it stands as a model for future waste management solutions that prioritize eco-friendliness and efficiency. Through such technologies, we can better address environmental challenges and contribute to a more sustainable future.
Top Page Image Contents