Enviro 2100 Freestanding owner manual Through with a minimum 9 229 mm air space between the outer

Page 11
Method D. 2” (50.8 mm) Clearance to Combustible Wall Member: Start with a solid-pak listed factory built chimney section at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an inside diameter of 8” (2” [51 mm] larger than the 6” [152.4 mm] chimney connector). Use this as a pass-through for a minimum 24 gauge single wall steel chimney connector. Keep solid-pak section concentric with and spaced 1” (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening with and support chimney section on both sides with 24 gauge minimum sheet metal supports. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure chimney flue liner.
Method A. 12” (304.8 mm) Clearance to Combustible Wall Member: Using a minimum thickness 3.5” (89 mm) brick and a 5⁄8” (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. The clay liner must conform to ASTM C315 (Standard Specification for Clay Fire Linings) or its equivalent. Keep a minimum of 12” (305 mm) of brick masonry between the clay liner and wall combustibles. The clay liner shall run from the brick masonry outer surface to the inner surface of the chimney flue liner but not past the inner surface. Firmly grout or cement the clay liner in place to the chimney flue liner.

Installation

CHIMNEY INSTALLATION THROUGH WALL:

Here are four methods of combustible wall chimney connector pass-throughs. This information was provided from NFPA 211.

A

 

Method B. 9” (229 mm) Clearance to Combustible Wall Member:

B

Using a 6” (152 mm) inside diameter, factory-built Solid-Pak chimney

 

section with insulation of 1” (25.4 mm) or more, build a wall pass-

 

through with a minimum 9” (229 mm) air space between the outer

 

wall of the chimney length and wall combustibles. Use sheet metal

 

supports fastened securely to wall surfaces on all sides, to maintain

 

the 9” (229 mm) air space. When fastening supports to chimney

 

length, do not penetrate the chimney liner (the inside wall of the

 

Solid-Pak chimney). The inner end of the Solid-Pak chimney section

 

shall be flush with the inside of the masonry chimney flue, and

 

sealed with a non-water soluble refractory cement. Use this cement to also seal to the brick masonry penetration.

Method C. 6” (152.4 mm) Clearance to Combustible Wall Member:

CStarting with a minimum 24 gauge (.024” [0.6 mm]) 6” (152.4 mm) metal chimney connector, and a minimum 24 gauge ventilated wall thimble which has two air channels of 1” (25.4 mm) each, construct a wall pass-through. There shall be a minimum 6” (152.4 mm) separation area containing fiberglass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble, and cover its opening with a 24 gauge minimum sheet metal support. Maintain the 6” (152.4 mm) space. There should also be a support sized to fit and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all

sides. Make sure fasteners used to secure the metal chimney connector do not penetrate chimney flue liner.

D

NOTES:

1.Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through system and the chimney wall, to but not past the inner flue liner face.

2.A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor, or ceiling.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Wood Stove Safety Precautions Table of Contents Operating Instructions Building/Maintaining a Fire MaintenanceChimney or RUN Away Fire Fuel SelectionFor Maximum Efficiency Refueling the StoveWhat does dry, seasoned wood mean? Why can’t I get the fire lit?What is draft? What type of wood is best to use as firewood?What can cause a poor draft? Model Freestanding SpecificationsInstallation Through with a minimum 9 229 mm air space between the outer Installation Outside AIR Total Bricks Glass is Broken Optional FAN Installation Parts List PartsDiagram Warranty Exclusions and Limitations Warranty Installation Data Sheet

2100 Freestanding specifications

The Enviro 2100 Freestanding is an exceptional wood stove designed to combine efficiency, style, and functionality. This modern stove is crafted for homeowners seeking an environmentally friendly heating solution without sacrificing aesthetics or performance.

One of the standout features of the Enviro 2100 is its impressive heating capacity. With the ability to effectively heat spaces of up to 2,000 square feet, it provides an ideal solution for large living areas or open floor plans. The efficient heat output ensures that rooms maintain a consistent and comfortable temperature, even during the coldest winter months.

The Enviro 2100 incorporates advanced clean burning technologies that significantly reduce emissions while maximizing heat production. Its innovative design allows for a secondary combustion system that ignites and burns off unburned gases and particulates. This not only minimizes the environmental impact, but also enhances fuel efficiency, giving homeowners more warmth for less wood consumption.

Durability and craftsmanship are also key characteristics of the Enviro 2100. Constructed from high-quality steel and featuring a cast iron door, this stove is built to withstand the demands of daily use. The large firebox is designed for easy loading, accommodating larger logs for longer burn times, thus reducing the frequency of reloading.

Aesthetically, the Enviro 2100 Freestanding stove offers a range of customization options. Buyers can choose between various finishes, including classic black or a more contemporary brushed nickel, allowing them to match the stove with their home décor. Additionally, the large glass viewing window provides an alluring glimpse of the flickering flames, creating a cozy ambiance in any setting.

Safety features are thoughtfully integrated into the design of the Enviro 2100. The stove includes a built-in air wash system that helps keep the glass clean, ensuring a clear view of the fire while contributing to overall safety. Furthermore, the unit is equipped with a heat shield, allowing for closer placement to walls without compromising safety or performance.

In summary, the Enviro 2100 Freestanding is a standout choice for those seeking an efficient and stylish wood heating solution. With its impressive heating capacity, advanced clean burning technologies, durable construction, customizable design, and essential safety features, it is truly a remarkable addition to any home. Whether for functional warmth or aesthetic value, the Enviro 2100 promises to deliver an exceptional experience for years to come.
Top Page Image Contents