Desa Tech S39NT installation manual Installing Logs, Installing Optional Blower Accessory GA3750

Page 10

VENT-FREE NATURAL GAS PEDESTAL STOVE

INSTALLATION

Continued

INSTALLING LOGS

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION:Afterinstallationand periodically thereafter, check to en- surethatno flamecomes incontact with any log. With the heater set to High, check to see if flames contact any log. If so, reposition logs ac- cording to the log installation in- structions in this manual. Flames contacting logs will create soot.

It is very important to install the logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

Place one-piece log set on grate to fit as illustrated in Figure 10. Make sure log sits flat on firebox floor (see Figure 9).

IMPORTANT: Make sure log does not cover any burner ports (see Figure 10).

One Piece

Log Set

Firebox Floor

Figure 9 - Installing One-Piece Log Set

Burner Ports

One Piece Log Set

Figure 10 - Installing One-Piece Log set (Top View)

INSTALLING OPTIONAL BLOWER ACCESSORY GA3750

Tools required: Phillips screwdriver

NOTICE: Shut off gas heater during the following blower installation.

1.Remove 2 screws from rear tabs on top trim. Pull trim forward to remove (see Figure 11).

2.Remove top panel of stove by remov- ing three screws from under top lip on each side of stove (see Figure 11).

3.Facing front of stove, carefully slide top panel forward until it is completely re- moved from stove (see Figure 11).

4.Install one plastic bushing provided in blower kit into the 1 1/2" hole in the left rear of firebox floor. Access hole through the rectangular opening in the rear panel (see Figure 12).

5.Disconnect power cord wires from blower motor (if connected) (see Figure 13).

6.Disconnect green ground wire from blower housing (if connected) by re- moving screw holding wire terminal (see Figure 13).

7.Remove the two blower mounting brackets from the rear panel by remov- ing two screws each (see Figure 14).

Screws

Top Top Panel

Trim

Screws

Figure 11 - Removing Stove Top Panel

Figure 12 - Installing Bushing

8.Attach the two mounting brackets to blower housing using four screws pro- vided in blower kit (2 for each bracket) (see Figure 14). Tighten screws se- curely. Place blower assembly tempo- rarily on top of firebox.

9.Working from the rear of the stove, place entire power cord, including speed control housing, in lower control compartment.

10.Route ends of 3-wire power cord up from the lower control compartment through the plastic bushing, then up to the upper cavity of stove (see Figure 15, page 11).

11.Attach the terminal ends of the white and black power cord wires to the ter- minals on the blower motor (see Fig- ure 12). Push firmly.

12.Attach the terminal end of the green power cord wire to the front tab of the blower housing using screw provided (see Figure 13).

White

Powercord

Wire

Screw

Green

Ground Wire

Black Powercord Wire

Figure 13 - Removing Wires from Blower

Screws

Blower

Bracket

Blower

Screws

Firebox Top

Figure 14 - Removing Blower Brackets from Stove and Attaching to Blower

For more information, visit www.desatech.com

10

107434

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OWNER’S Operation and Installation Manual VENT-FREE Natural GAS Freestanding Pedestal Stove SystemSafety Information VENT-FREE Natural GAS Pedestal StoveLocal Codes Product Identification FeaturesSafety Pilot UnpackingUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Clearances to Combustibles InstallationCheck GAS Type Minimum Wall and Ceiling Clearances see FigureConnecting to GAS Supply Installation Items NeededPressure Testing Heater Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Installing Logs Installing Optional Blower Accessory GA3750Installing Optional Blower Accessory GA3650TA Vided in blower kit 2 for each bracketRemoving Cover Plate Operating Heater For Your Safety Read Before LightingLighting Instructions Inspecting Burners Cleaning and Maintenance Troubleshooting Observed Problem Possible Cause RemedyNance, Top Technical Service SpecificationsService Hints Parts CentralsIllustrated Parts Breakdown S39NTParts List KEY Part Number Description QTY2611 KEY Description QTY Replacement Parts Accessories107434 Warranty Information International

S39NT specifications

Desa Tech S39NT is an innovative technology that has gained attention for its impressive capabilities in the realm of connectivity and performance. This device is designed to cater to the demands of both consumers and businesses, providing a seamless experience through a variety of features.

One of the standout characteristics of the S39NT is its powerful processing unit, which allows for rapid data processing and multitasking capabilities. This ensures that users can run multiple applications simultaneously without experiencing lag or performance issues. The device is equipped with advanced cooling technologies, which maintain optimal performance levels even during intense workloads.

The S39NT also boasts connectivity options that are second to none. With support for the latest Wi-Fi standards, including Wi-Fi 6, users can enjoy incredibly fast internet speeds and reduced latency, making it an excellent choice for gaming, video streaming, and other data-intensive activities. Furthermore, the device features multiple USB ports, including USB-C, enhancing compatibility with various peripherals and ensuring efficient data transfer.

In terms of storage, the Desa Tech S39NT offers an array of options to cater to different user needs. With solid-state drive (SSD) technology integrated into its design, users benefit from rapid boot times and quick access to applications and files. This not only boosts productivity but also enhances the overall user experience.

In addition to its hardware specifications, the S39NT is built on a robust software platform. It operates on a user-friendly interface that simplifies navigation and customization. Regular updates ensure that users have access to the latest features and security enhancements, protecting their data and privacy.

Moreover, the design of the S39NT reflects a modern aesthetic, combining functionality with stylish appeal. Its lightweight build makes it an ideal choice for professionals and students on the go, while its durable materials ensure it can withstand everyday wear and tear.

In summary, the Desa Tech S39NT stands out due to its powerful performance, extensive connectivity options, fast storage solutions, intuitive software environment, and attractive design. It is an ideal option for anyone looking to enhance their digital experience, combining versatility with cutting-edge technology. Whether for personal or professional use, the S39NT is engineered to meet the evolving needs of today’s users, ensuring they stay ahead in a competitive digital landscape.
Top Page Image Contents