Desa Tech S39NT installation manual Removing Cover Plate

Page 12

VENT-FREE NATURAL GAS PEDESTAL STOVE

INSTALLATION

Continued

11.Remove three screws and cover plate from center of firebox back panel. Keep screws but discard cover plate (see Figure 17).

12.Locate thermostatic switch/cover plate assembly and wire harness supplied with blower. Attach wire harness ter- minals to terminals on thermostatic switch. Push firmly. Make sure the bot- tom hole of cover is on the opposite side from the wire harness (see Figure 18).

13.Feed terminal ends of wire harness into the hole in firebox back panel from front of firebox. Pull the ends of the harness to the top of firebox near blower (see Figure 19).

14.Align holes in the switch/cover assem- bly with holes in firebox back panel. Using 3 screws from step 11, attach assembly to firebox back panel. Tighten screws firmly (see Figure 19).

15.Working from the rear of the stove, place entire power cord, including speed control housing, in lower control compartment (see Figure 20).

Cover

Plate

16.Route ends of 3-wire power cord up from the lower control compartment through the plastic bushing, then up to the upper cavity of stove (see Figure 20).

17.Connect white wire from speed control to either terminal on blower motor (see Figure 20). Push firmly.

Thermostatic

Switch Wire Harness Mounted to

Cover

Hole in Firebox Back Panel

Wire Harness

Screws

Figure 19 - Assembling Thermostatic Switch and Cover to Firebox Back Panel

Green

White Speed

Control Wire

Ground

Black

Wire

Blower

Speed

Control

 

Wire

18.Connect the black wire from speed con- trol to blue wire on switch/cover assem- bly (see Figure 20).

19.Connect red wire from switch/cover assembly to remaining terminal on blower motor (see Figure 20). Push firmly.

20.Attach green wire from speed control to front tab of blower housing using screw provided (see Figure 20). Tighten securely.

21.Using the four screws previously re- moved, mount blower assembly to stove by reattaching blower brackets to rear panel (see Figure 14, page 10). Tighten screws securely.

22.Install plastic control knob onto output shaft of speed control housing (see Fig- ure 20). Place speed control housing just inside control compartment door in front of stove (see Figure 16, page 11).

23.Using two screws provided in blower kit, mount blower speed control hous- ing to mounting tab in left side of lower control compartment (see Figure 16, page 11).

24.Check to make sure that the power cord is completely clear of blower wheel and there are no foreign objects in blower wheel.

25.Carefully replace stove top panel. Align holes and replace six screws removed in step 1, page 11. Slide top trim over sides of top panel. Attach with 2 screws removed in step 1, page 11.

Screws

Firebox Back Panel

Figure 17 - Removing Cover Plate

Lower Hole

Thermostatic Switch Mounted to Cover

Wire Harness

Figure 18 - Attaching Wire Harness to Thermostatic Switch and Cover Assembly

Ground

 

Wire Screw

Blue

 

Red

Switch

Switch

Wire

Wire

Power

 

Cord

 

Wiring

 

Diagram

 

Decal

Control

Speed Control

Knob

Housing

Figure 20 - Connecting Switch, Blower, and Speed Control Wires

WARNING: Never attempt to service heater while it is plugged in, operating, or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater.

If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 105° C wire or it’s equivalent.

WARNING: Label all wires prior to disconnection when servicing controls. Wiring errors can cause im- proper and dangerous operation. Verify proper opera- tion after servicing.

Variable

Fan SwitchFan Switch

(N.O.)

Off 1

2 Black

 

 

On

Blue

 

 

Red

110/115

V.A.C.

Black

GreenBlower

WhiteMotor

120 Vac. 60 Hz. 90 Amps

DESA International, Bowling Green, KY

For more information, visit www.desatech.com

12

107434

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OWNER’S Operation and Installation Manual VENT-FREE Natural GAS Freestanding Pedestal Stove SystemSafety Information VENT-FREE Natural GAS Pedestal StoveProduct Identification Features Safety PilotLocal Codes UnpackingAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeClearances to Combustibles Minimum Wall and Ceiling Clearances see FigureConnecting to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsChecking GAS Connections Installing Logs Installing Optional Blower Accessory GA3750Installing Optional Blower Accessory GA3650TA Vided in blower kit 2 for each bracketRemoving Cover Plate For Your Safety Read Before Lighting Operating HeaterLighting Instructions Inspecting Burners Cleaning and Maintenance Troubleshooting Observed Problem Possible Cause RemedyNance, Top Specifications Service HintsTechnical Service Parts CentralsIllustrated Parts Breakdown S39NTParts List KEY Part Number Description QTY2611 KEY Description QTY Replacement Parts Accessories107434 Warranty Information International

S39NT specifications

Desa Tech S39NT is an innovative technology that has gained attention for its impressive capabilities in the realm of connectivity and performance. This device is designed to cater to the demands of both consumers and businesses, providing a seamless experience through a variety of features.

One of the standout characteristics of the S39NT is its powerful processing unit, which allows for rapid data processing and multitasking capabilities. This ensures that users can run multiple applications simultaneously without experiencing lag or performance issues. The device is equipped with advanced cooling technologies, which maintain optimal performance levels even during intense workloads.

The S39NT also boasts connectivity options that are second to none. With support for the latest Wi-Fi standards, including Wi-Fi 6, users can enjoy incredibly fast internet speeds and reduced latency, making it an excellent choice for gaming, video streaming, and other data-intensive activities. Furthermore, the device features multiple USB ports, including USB-C, enhancing compatibility with various peripherals and ensuring efficient data transfer.

In terms of storage, the Desa Tech S39NT offers an array of options to cater to different user needs. With solid-state drive (SSD) technology integrated into its design, users benefit from rapid boot times and quick access to applications and files. This not only boosts productivity but also enhances the overall user experience.

In addition to its hardware specifications, the S39NT is built on a robust software platform. It operates on a user-friendly interface that simplifies navigation and customization. Regular updates ensure that users have access to the latest features and security enhancements, protecting their data and privacy.

Moreover, the design of the S39NT reflects a modern aesthetic, combining functionality with stylish appeal. Its lightweight build makes it an ideal choice for professionals and students on the go, while its durable materials ensure it can withstand everyday wear and tear.

In summary, the Desa Tech S39NT stands out due to its powerful performance, extensive connectivity options, fast storage solutions, intuitive software environment, and attractive design. It is an ideal option for anyone looking to enhance their digital experience, combining versatility with cutting-edge technology. Whether for personal or professional use, the S39NT is engineered to meet the evolving needs of today’s users, ensuring they stay ahead in a competitive digital landscape.
Top Page Image Contents