Euro-Pro UV647H owner manual Changing the Rotating Brush, Gear Box & Squeegee, Changing the Belt

Fig. 16

Changing the Rotating Brush, Gear Box & Squeegee

WARNING: Use caution when changing the rotating brush and gear box so that the unit does not turn ON when pressing down on the sweeper power head.

1.Remove the extension tube handle from the sweeper power head.

2.Turn sweeper power head upside down being careful Not to accidentally turn the unit ON.

3.Remove the brush cover. (Fig. 10) (Refer to page 5 for detailed instructions.)

4.Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 11 & 12)

5.Lift the brush bar end cap up from the slot. (Fig. 13)

6.Pull the brush bar out of the bushing and slip off the belt to remove the brush bar. (Fig. 14)

7.Insert the new brush bar by first inserting the brush bar into the bushing on the end opposite the driver belt. (Fig. 14)

8.Slip the belt over the brush bar cap.

9.Insert the brush bar into the slot. (Fig. 13)

10.Insert the gear box tabs into the tab slots and push down until it clicks into place.

11.To replace the squeegee, follow instructions above for removing the gear box and slide the squeegee out from left to right. (Fig. 15)

Gear box	Locking	Lift
	tab

Fig. 10 Gear box tabs Fig. 11 Fig. 12

Slide

Fig. 13 Fig. 14 Fig. 15

Changing the Belt

If you find that the belt has broken and it needs replacing:

1.Remove the brush cover. (Fig. 10)

2.Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 11 & 12).

3.Push in on the locking tab of the belt access panel and lift off to remove. (Fig. 16)

4.Using a pair of tweezers, remove any leftover bits of the

belt that might still be there.

5.Pull the brush bar out of the bushing. (Fig. 13)

6.Using a new belt, insert it into the opening until it is in all the way.

7.Using a pair of tweezers, insert them into the belt access panel and lift the new belt over the back gear.

8.Slide the belt over the brush bar cap and then insert the brush bar into the slot. (Fig. 13)

9.Insert the gear box tabs into the tab slots and push down until it clicks into place.

10.Press the belt access panel down until it snaps in place.

11.Replace the brush cover (Fig. 10)

7

How to Operate Your Cordless Sweeper

1.Before using, please ensure that the cordless sweeper has been initially charged for 20 hours

Your cordless sweeper will only operate properly when the batteries are fully charged. Your sweeper will operate for varying lengths of time on a full charge. This will depend upon the type of surface being cleaned. (Longer operating time on bare floors vs carpets.)

2.Push the On/Off switch to operate the unit. To turn off, press switch again.(Fig.4)

"On/Off" switch

Fig. 4

CAUTION: Any electronic or electrical appliance should not be stored in or exposed to areas of high heat or humidity. Do not store your cordless sweeper close to stoves, radiators, furnaces or in a bathroom or bathing area.

3.To release the handle to a comfortable position, apply pressure to the top of the sweeper head with your foot while pulling back on the handle.(Fig. 5)

Fig. 5

4.To change the speed of the sweeper, press on the speed control button. As you press on it, the speed indicator light will change. If one light lights up, then you have the low speed; two lights, medium speed; three lights, high speed.

5.If something were to jam or overload the brush bar system, the units speed indicators will flash and the unit will stop operating, this is normal. To reset the unit, remove the tangled object and then depress the on/off switch once and then depress it again to restart the unit.

4