Euro-Pro EP619 Winding & Unwinding the Power Cord, Using the Unit with the Accessories

Fig. 12

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

WINDING & UNWINDING THE POWER CORD

USING THE UNIT With the Motorized Floor Brush

Extension Tube

For hard to reach places. Use with

4. Remove the brush cover. (Fig. 10)

This vacuum cleaner is equipped with a convenient cord storage feature. The power cord winds around the two cord holders at the back of the unit. The top one has a quick

cord release feature. Turn the cord hook to the left or the right to remove the power cord. (Fig. 4)

When using the vacuum, attach the power cord to the cord holder so that the power cord is out of the way when you

are vacuuming. (Fig. 5)

Fig. 5

Fig. 4

Cord holder

•Unwind the power cord and plug into the 120V outlet.

•Press the On/Off switch to the “II” position so that both the vacuum

and the motorized

floor brush isLower turned “ON”

NOTE: When vacuuming
deep pile carpets or
hard wood floors,
lower the angle
of the handle (see
illustration at
right) for easier
maneuverability.
(Fig. 7)	Fig. 7

USING THE UNIT WITH THE ACCESSORIES

crevice tool or with dusting brush.

Crevice Tool

For radiators, crevices, corners, baseboards and between cushions.

Dusting Brush

The dusting brush is used for the furniture, venetian blinds, books, lamp shades and shelves.

Intelli-SenseTMFilter Monitor

When the Intelli-SenseTMFilter Monitor lights up, it means that the dust cup is full or the HEPA filter, filter ring or Debris Screen needs cleaning. You must empty the dust from the

Fig. 10

5.To gently remove the object, hair or fibers pull slowly to release. Removing with scissors may be necessary, however, avoid damaging or cutting the bristles.

Emptying the Dust Cup Container Important: Do NOT use the vacuum without ALL the filters in place.

Warning: Always unplug the unit from electrical outlet before opening the Dust Cup (container).

1.To remove the dust cup container, turn the dust cup release lever to the right. (Fig. 11)

ON/OFF SWITCH

The On/Off switch has three different positions. (Fig.6)

•Push on the "I" side to turn the vacuum ON. Set the vacuum here when using the removable hose handle with the accessories or when vacuuming bare floors.

•Push on the “II" side to turn the motorized floor brush on.

•Push on the “O” side to turn the vacuum to the OFF position.

=OFF

= Vacuum ON

Motorized Floor

=Brush ON Fig. 6

•Remove the removable hose handle from

the hose connector.

•Attach the extension tube, crevice tool or the dusting brush to the end of the hose. (Fig. 8)

Fig. 8

MANUAL VARIABLE SUCTION CONTROL

Your vacuum cleaner includes a variable suction control valve on the hose extension. The suction power can be adjusted by moving the slide to the desired position. For example. Less suction is required on upholstery and draperies compared to thick shag carpets, which require maximum suction.

dust cup and clean the HEPA filter and Debris Screen right away.

Brush Roll Warning Light

If while using the motorized floor brush the brush becomes jammed or picks up an object which causes the brush roll to cease revolving, the red indicator light will illuminate. In this case:

Brush Roll

Warning Light

1.Turn unit “Off” and unplug from wall outlet.

2.Remove the motorized floor brush from the main unit.

3.Use a Phillips #1 screwdriver and remove the two (2) front screws from the bottom of the motorized floor brush. (Fig. 9) Screws

Fig. 11

2.Remove the dust cup from the vacuum. (Fig. 12)

3.To empty the dust cup container, hold the dust cup from the handle over a garbage container and

press on the trap door release button that is on the front side of the dust

cup container to release the dust cup bottom (Fig. 13)

5

Fig. 9

Fig. 13

6