Using Your Cleaner, Cleaner Maintenance

USING YOUR CLEANER

1.Extract power cord and plug it into the power supply. Do not pull the cord beyond the red marker. [5]

2.Adjust the telescopic tube to the desired height by moving the telescopic release button up and raise or lower the handle to the most comfortable cleaning position.

[6]

3.Carpet and Floor Nozzle** - Select the type of surface to be cleaned by pressing the pedal** in the nozzle. [7]

Hard Floor – Brushes are lowered to protect the floor.

Carpet – Brushes are raised for the deepest clean.

4.Switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]

CLEANER MAINTENANCE

Emptying the Dust Container

When the dust reaches the max level indicator in the container empty the dust bin.

IMPORTANT:To maintain optimum performance do not allow the dust to sit higher than the max level.

1.Release the container by sliding the dust container release button towards the rear of the cleaner. Lift the dust container from the cleaner main body. [14]

2.Hold the dust container over a bin with one hand and use the other hand press the

Dust Container Door Release Button. [15]

3.Close the Dust Container door and refit to the cleaner main body.

5. Adjust the suction by moving the suction regulator to the desired level.* [9]	Cleaning the washable filters
6. Switch off at the end of use by pressing the On/Off Button. Unplug and press the	The cleaner is fitted with a blue filter pack. To maintain optimum cleaning performance
cord rewind button to wind the power cord back into the cleaner. [10]	regularly remove the the filters and tap against the side of the bin to release dust. The filters
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the	should be washed after 5 container empties or when the filter has excessive dust level.

nozzle in the parking slot on the cleaner main body. [11]	IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean

ACCESSORIES AND NOZZLES	your filters may result in air blockage, overheating and product failure. This may
ACCESSORIES AND NOZZLES	invalidate your guarantee.
	invalidate your guarantee.
All accessories can be fitted to the end of the hose handle or to the end of the telescopic tube.	IMPORTANT: Regularly check and maintain the filters by following the filter main-
2 in 1 tool – Combines several functions in one. [12]	tenance instructions , it is also recommended that you purchase new filters after
2 in 1 tool – Combines several functions in one. [12]	every 3rd filter wash. This will maintain your cleaners performance.
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To ex-
tend the brushes push the button on the body of the tool.	IMPORTANT: Always ensure the filters are fully dry before use.
Crevice Tool – For corners and hard to reach areas.
Furniture Nozzle – For soft furniture and fabrics [13]	To access the pre-motor filter:
Furniture Nozzle – For soft furniture and fabrics [13]	1.	Release the container by sliding the dust container release button towards the rear
Parquet Caresse Nozzle* – For parquet floors and other delicate floors. [1U]		of the cleaner. Lift the dust container from the cleaner main body. [14]
	2.	Hold the dust container with one hand and with the other hand rotate the bin handle
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep-		anti clockwise to release it from the dust container. [16]
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet	3.	Remove the blue filter pack located in the dust container handle. [17]
hairs removal. [1V]	4.	Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for		Remove excess water from the filter and leave to dry fully before re-using. [18]
deepcleaning on textile surfaces and other hard to clean areas. Particularly suitable for	5.	Reassemble to filter pack once fully dry and refit to the cleaner.
allergen removal. [1W]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]	IMPORTANT: Do not use the product without the filter pack fitted.
IMPORTANT: Do not use the grand turbo and mini turbo nozzles on rugs with long	To access the exhaust filter:
fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle station-	1.	Release the container by sliding the dust container release button towards the rear
ary while the brush is rotating.		of the cleaner. Lift the dust container from the cleaner main body. [14]
	2.	Unclip the exhaust filter cover from the dust container cradle on the cleaner main
		body. [19]
	3.	Using the tab remove the exhaust filter from the cleaner main body. [20]
	4.	Gently tap and wash the filter using warm water. Do not use hot water or detergents.
* Certain models only	2	Remove excess water from the filter and leave to dry fully before re-using. [21]
	2

** May vary depending on model

Curve im uk master.indd 2

3/28/2012 1:49:19 PM