Hoover 56518114 manual Ii..-!iZ,ii!b.JD

To clean the outside of the machine,

Keep nozzle fiat on floor for both for-

wipe	off dirt	with	a cloth	dampened	in
waI'lTI	water	and	mild	detergent,	DO not

use solvent or petroleum based prod- ucts to clean the machine.

Read "Before you begin cleaning" instructions on page 9.

1 , Fill clean _;olution tank (upper tank)

with HOOVER Carpet/U pholstery

aet[_'rgent according to instructions for

Figs, 2-8 to 2-14.

2.Move speed selector to LO for gen- tle cleaning or HI for normal cleaning.

3, Dry hands and plug cord into a prop-

erly grounded outlet.

Do not clean over floor electrical out- lets.

4.To avoid walking on damp carpet,

start at the end of the room farthest from

the door Or path to sink where tanks will

be emptied and filled,

Step on handle release pedal and lower

handle to operating position; turn deep

cleaner ON,

/ /

5,

Squeeze

trigger

to

release

cleaning

solution

and

SlOWly

push

deep

cleaner

forward

(equals

one

wet

stroke),

6,

Continue

to

squeeze

trigger

and

SlOWly

pull

deep

cleaner

back

toward

you

(s_;cond

wet

stroke).

Release

trigger

and

slowly

push

deep

cleaner

forward

over

area

just

sprayed

with

solution

(dry

stroke),

Then

slowly

pull

deep

cleaner

back

toward

you

without

squ[;[_.zing

trig-

ger

(dry

stroke).

7,

Overlap

strokes

by ]

inch

to

help

pre-

vent

streaking,

Your deep cleaner may also be used to

pick up small liquid spills (1 gallon or less, never to exceed 1/4 inch in

depth) on carpet, upholstery, or bnr_

floors,

ward and reverse strokes,

8. For heavily soiled areas, repeat steps

5-7,Avoid saturating carpet, as noted

below.

9, For	particularly		soiled		carpet		or
spots,	use	the	Clean	Surge		TM	button
(see	following		section),		Avoid		saturating
carpet,	as	noted	below,

Note: To avoid saturating carpet, do not use more than 4 wet strokes over

one area. Always end with dry strokes.

It is best to alt(_-rnatc_ wet and dry

strokes as described above,

For	[lest		cleaning			results		and	to	aid in
faster		drying		of	carpet,		end		with	more
dry	strokes,			(Continue			using		dry	strokes
until	littte		water		is	visible		passing
through		the		recovery			tank	lid	,)
Empty		recovery			tank		when	the		motor
sound		becomes				higher	pitched			and
thn.rt-_ is a				loss	in	suction		(see
"Automatic				shut-off",			Fig,	2-6)
When		finish_.d			cleaning,			follow		"After
cleaning"				instructions			on	pages		9,

When picking up spills on bare floors, use only the floor nozzle with the bare floor attachment (some models) in place and speed selector in the OFF position

(this wllI h(;Ip p_vent spr_zoding the spill),

if a spot	is loll,	the	stairfupholstery		rlozzIu	is
generally	more	effective		for removing	it,

. :._ii.".-!::_i;_Z,ii!b._JD'

i!!:i:i:i!i_i!i!!.._:::":4 / ///

CleanSurge TM Button

(some models)

The 'Clean Surge' button can he used to

dispense extra solution when cleanJlhg

particularly soiled areas of carpet or spots,

To	use,	press		'Clean		Surge'	button	While
squeezing			solution		trigger,		For normal
solution		spray,		release		button	and	contin-
ue	to	squeeze		solution		trigger,

1. For

best

results,

pick

up

spills

imme-

diately

by placing

the

stair/upholstery

nozzle

just

above

the

spill

and

suction

up

any

r_-.sidue

on

top

of

the

carpet,

2, If

the

spill

remains,

place

either

the

stair/

upholstery

nozzle

or

floor

nozzle

with

brushes

turned

OFF

in

fl'ont

of

the

spill,

pull

the

nozzle

very

slowly

over

the

spill

initially

with

suction

only.

Re.peat

with

spray

and

suction,

Although		no	cleaning	solution		can com-
pletely		remove	all	spots,	they	can	be treat-
ed	by	following	the	instructions			provided
by	the	manufacturer		of the carpet,			uphol-
stery,		or bare	floor	surface	being		cleaned,

Do not use the deep cleaner to pick up

flammable or combustible liquids or

chemicals.

Wh_;n fini_;h_-d, follow "Aftnr ck_anlng"

instructions on pages 9,

How to attach bare floor

at_ta c h m e nt (some models)

Disconnect deep cleaner from electri- cal outlet.

To prevent		possible			leaking,		remove
clean	solution		tank		(Fig,	2-8)	and	recov-
ery	tank	(Fig,	2-15)		before		positioning
bare	floor	attachment,
Set	tanks	asid{;	(do		not	set	tank	on furni-
ture).
1. With		handle	In	upright		position,		tilt
cleaner		back	so	that	handle		rests	on the
floor,
10

2. With fonm strip (A) 0o_ated und(;r the

3. Push attachment

against

nozzle

while

netting)

in

position

as

shown,

place

rotating

attachltlent

downward

until

both

attachment

on

front

of

nozzle;

(B).

ends

snap

into place,

Make sure

arrow

on

{znd

of

attachment

(Note:

Some force

may be required

to

points

in tiqe direction

as

shown,

rotate

and

snap attachment

into place.)