Eureka 4390 Series, 4490 Series HOW to Maintain, Use 15 watt replacement light bulb, part number

HOW TO MAINTAIN (continued)

How To Change Light Bulb (only for models with a headlight)

NOTE: Turn off the power switch and disconnect the electrical cord before changing light bulb.

1.Lower handle. Remove two screws from lens cover.

2.Pull lens cover from cleaner.

3.Pull light bulb and socket toward front.

4. Push light bulb into socket; turn to release.

5.Place new light bulb into socket; turn to secure.

6.Push light bulb and socket back so bulb will not touch lens cover.

7.Replace lens cover.

8.Secure with two screws.

Use 15 watt replacement light bulb, part number 48815.

Problem Solving NOTE: Turn off the switch and unplug electrical cord before servicing.

			PROBLEM�	CAUSE�	SOLUTION
Motor will not start				Electric Plug	Push plug securely into outlet.
					Try another outlet.
					Check circuit breaker.
Motor suddenly				Thermal Cut Off	Refer to page 3 & 5.
stops
Does not clean the				Filters	Clean or replace the filter(s). Hint: If picking up fine dust, the
carpet or floor.					filter may not look dirty but a fine substance tends to reduce
					suction when it blocks the airflow through the filter(s).
				Cyclonic Cassette	Be sure hose adapter inserts into cyclonic cassette.
					Be sure the cyclonic cassette is properly seated into the cassette
					body. See page 4.
					Empty cyclonic cassette. Note: There are two chambers in the
					cyclonic cassette. The chamber with the screen will fill much
					faster than the chamber with the cone. This is normal, when the
					chamber with the screen is full, empty cyclonic cassette, do not
					wait till the chamber with the cone is full. See page 7.
				Belt	Replace a cut, loose or out of shape belt.
				Belt Cap	Snap the belt cap inside the hood if it comes loose.
				Brush Roll	Clean hair and thread from bristles and end cap area.
					Replace brush roll if bristles are worn.
				Hose	Remove any clogs from the hose that restrict the airflow. Check
					short hose in the base and long hose. Refer to page 9.
No suction at the				Hose Adapter	Hose adapter has to seat inside the cyclonic cassette. Hint: Put
end of the hose.					the hose in place before attaching the handle. The handle
					secures the hose.
				Filter(s)	Clean or replace the filter(s). Hint: If picking up fine dust, the
					filter may not look dirty but a fine substance tends to reduce
					suction when it blocks the airflow through the filter(s).
				Hose	Remove any clogs from the hose that restrict the airflow. Check
					short hose in the base and long hose. Refer to page 9.
	Headlight not			Light Bulb	Replace light bulb.
working.
		Noise from the		Brush Roll	Remove hood and clean debris or items from the brush roll area.
brush roll area.				Belt	Replace a cut, loose or out of shape belt.
Cleaner is hard to				Cleaner Height Setting	Put handle in operating position. Tilt the cleaner back to raise the
push.					front wheels off the floor. Then turn the knob to a higher setting.
				Belt	Replace a cut, loose or out of shape belt.
			Cleaning height	Cleaner Height Setting	Hint: Put handle in operating position. Tilt the cleaner back to
knob will not turn.					raise the front wheels off the floor. Then turn the knob.
			Missing parts.		Call 1-800-438-7352 between 8:00 a.m. and 4:45 p.m., central
					standard time, Monday through Friday. Know the model and
					serial numbers when you call.
			Questions?		Call 1-800-282-2886 8 a.m. to 7:30p.m., (CST), Monday -
					Friday and 10 a.m. to 6:30 p.m. (CST) Saturday. Know the	11
					model and serial numbers when you call.