Bissell 57F4 warranty Before you clean, Steam cleaning hard floors, Used as both a steam mop and a

Page 8

Operations

Before you clean

 

1.

The Steam & Sweep can be used

 

 

 

as a sweeper and a steam mop

Brush Switch

Power Switch

at the same time. For best results,

 

 

use the Steam & Sweep's powerful

 

 

sweeper to clear floor of dust and

 

 

small debris before mopping.

 

 

1. Turn the brush switch to the On ( I )

 

 

position to activate the brush.

Dirt Bin

2.

 

2.To empty the dirt container, turn the Release Pedal power off, gently tap the release

pedal on the swivel head. Lift unit straight up leaving bin on floor and empty into a trash can. The dirt con- tainer may be warm to the touch.

3.Replace the dirt container by pushing it back into the swivel head until it snaps back into place.

 

Steam cleaning hard floors

 

 

WARNING:

 

 

Your Steam & Sweep is designed to

 

Never put descaling

 

 

clean hard flooring such as ceramic

 

aromatic, alcoholic, or

 

 

tile, vinyl, marble, stone and sealed

 

detergent products into

 

 

hard wood floors. Use of your

 

the steam cleaner, as this

 

 

Steam & Sweep on waxed or some

 

may damage it or make it

 

 

unwaxed floors may result in a

 

unsafe for use.

 

 

diminished glossiness. The Steam &

 

 

 

 

 

 

 

 

 

 

 

 

Sweep is not for use on unsealed

 

 

 

 

 

 

 

Tip:

 

 

wood floors. Ensure that the Steam

 

 

 

& Sweep is throughly tested in an

 

 

 

inconspicuous area prior to clean-

 

The Steam & Sweep may be

 

 

ing a large floor area. Also be sure

 

 

 

 

used as both a steam mop and a

 

 

to check the care instructions from

 

 

 

 

sweeper at the same time.

 

 

your flooring manufacturer.

 

 

 

1. When the ready light illuminates,

 

 

 

 

 

 

 

 

 

 

 

 

begin cleaning by slowly passing

 

 

 

 

 

 

steam on demand trigger to emit

 

 

 

CAUTION:

 

 

over the surface while pressing the

 

 

 

 

 

 

steam as needed.

 

 

 

The Steam & Sweep

 

 

 

 

 

 

 

2. To sanitize an area of your floor,

 

 

 

generates hot steam, so

 

 

 

 

 

when depressing the trigger

 

 

(attack invisible germs and bacteria)

 

 

 

 

 

 

 

 

to apply steam, ensure the

 

 

leave the Steam & Sweep over the

 

 

 

 

 

 

 

 

Steam & Sweep is mov-

 

 

area for a minimum of 15 seconds

 

 

 

 

 

 

 

 

ing continuously. Prolonged

 

 

using continuous steam, but no longer

 

 

 

 

 

than 20 seconds. For larger areas,

 

 

 

application of steam in one

 

 

overlap swivel head placement.

 

 

 

area increases the risk of

 

 

 

 

 

 

damage to the surface

 

 

3. When the Steam & Sweep stops

 

 

 

treatment of timber floors.

 

 

emitting steam, turn the unit off.

 

 

 

 

 

 

 

 

 

 

 

 

Simply remove the water tank, refill,

 

 

 

 

 

8

and continue cleaning.

 

 

 

 

 

w w w. b i s s e l l . c o m

 

 

 

 

 

Image 8
Contents Users Guide Thanks for buying a Bissell Steam & Sweep Read all instructions before using Steam & Sweep Reduce the risk of fire, electric shock, or injuryProduct view Secure the handle by placing the large AssemblyAttach handle to Steam & Sweep Special Features OperationsRemovable water tank Ready lightGetting ready Before you clean Steam cleaning hard floorsWhen depressing the trigger Used as both a steam mop and aReplacing the water purification system Maintenance and careWhen you’re done Troubleshooting Replacement parts Bissell Steam & SweepAdditional accessories Thank you for selecting a Bissell productWarranty Bissell Steam & Sweep Limited Two Year WarrantyBissell consumer services If your Bissell product should require service