Rheem Gas Heavy Duty Water Heater Models 265 Litre and 275 Litre Installation

Page 15

INSTALLATION

THIS WATER HEATER IS NOT SUITABLE FOR POOL HEATING

Check the water heater is suitable for the gas type available (refer to the rating label on the water heater)

Note: In Australia, natural gas models can be connected to SNG, however the hourly gas consumption may be reduced (typically by 10%).

WATER HEATER LOCATION

An indoor model must be installed indoors and an outdoor model must be installed outdoors, except where a 631 275 model water heater is installed indoors with a Rheem room sealed installation kit. The water heater should be installed either close to the most frequently used outlets or with a circulated flow and return system and its position chosen with safety and service in mind. Make sure people (particularly children) will not touch the flue outlet. The flue terminal must be clear of obstructions and shrubbery.

Clearance must be allowed for servicing of the water heater. The water heater must be accessible without the use of a ladder or scaffold. Make sure the temperature pressure relief valve lever is accessible and the front covers or panels, thermostats and burner can be removed for service.

You must be able to read the information on the rating plate. If possible leave headroom of one water heater length so the anode can be inspected or replaced. Remember you may have to take the entire water heater out later for servicing.

The installation must comply with the requirements of AS/NZS 3500.4, AS/NZS 3000, AS 5601 and all local codes and regulatory authority requirements. In New Zealand, the installation must conform with NZS 5261 Code of Practice for Installation of Gas Burning Appliances and the New Zealand Building Code.

The water heater must not be installed in an area with a corrosive atmosphere where chemicals are stored or where aerosol propellants are released. Remember the air may be safe to breathe, but when it goes through a flame, chemical changes take place which may attack the water heater.

For a single water heater installation, follow the diagrams on pages 22 and 23. For multiple water heater installations, follow the instructions on pages 32 to 36.

15

Image 15
Contents Owners Guide Installation Instructions Patents Contents Hotter Water Increases the Risk of Scald Injury Temperature AdjustmentAbout Your Water Heater Model TypeSafety To Turn on the Water Heater To Turn OFF the Water HeaterDoes the Water Quality Affect the Water HEATER? HOW Long will the Water Heater LAST?Anode Protection HOT Surface Ignition HOW Your Water Heater WorksMains Pressure Electronic ThermostatTemperature Pressure Relief Valve Regular CareExpansion Control Valve Servicing Not Enough HOT Water or no HOT Water Save a Service Call Diagnostic Features of Electronic Thermostat Water Heater not Operating Burner will not Light Expansion Control Valve Running Temperature Pressure Relief Valve RunningHigh GAS Bills Water Heater Appears to be LeakingInstallation This Water Heater is not Suitable for Pool HeatingWater Heater Location Safe Tray Indoor InstallationOutdoor Installation Mains Water Supply Tank Water SupplyHOT Water Delivery Circulated HOT Water Flow and Return System Temperature Limiting DeviceAnode Types Reducing Heat LossesSaddling Pipe Work Typical Installation Outdoor Location Typical Installation Indoor Location Model No 621265 631265 621275 631275 Dimensions and Technical DataConnections Plumbing Connection SizesWater Inlet and Outlet GAS Inlet Pipe SizesRelief Valve Relief Valve Drain Connections Electrical Thermostat SettingWiring a Power Flued System to the Water Heater Power Flue External Controls Intermittent Operation Power Flue External Controls 24 Hour Operation Multiple Installations Multiple Installations Typical Installation Rheem Heavy Duty GAS Water Heaters Line Manifold Back to Back Manifold Installation Dimensions Rheem Heavy Duty GAS Water HeatersManifold Arrangement To Fill and Turn on the Water Heater CommissioningGAS Inlet Pressure For Your Safety Read Before Lighting Lighting ProcedureLighting the Water Heater Flashes Fault Test the Water Heater After InstallationAIR Adjustment Burner Pressure AdjustmentDraining the Water Heater Recirculation System Temperature ControlThermostat Adjustment This page is intentionally blank Water Supplies AnodeSaturation Index Warranty Exclusions Warranty ConditionsRheem will Warranty