AquaStar 125FX NG, 125FX LP Mounting Installation, Incandescent Particle Tray Illustration

Page 6

MOUNTING INSTALLATION

The Aquastar 125FX is design certified for mounting on a wall.

Secure the two L shaped hooks, which are provided with heater, to a wall surface. Place them 13 ¼” apart as shown in Fig 2.

Do not install this appliance on a carpeted wall or over floor covering which is combustible, such as carpet. The heater must be mounted on a wall using appropriate anchoring materials. If wall is a stud wall sheathed with plasterboard, it is recommended that support board(s) either 1x4’s or 1/2" (minimum) plywood first be attached across a pair of studs and then the heater should be attached to the support boards. See Fig 2.

NOTE: Additionally the 125FX should be spaced away from any combustible wall surface to provide the necessary clearance that the venting material specifies must be maintained between the vent pipe and a combustible surface. See VENTING section. Also, review the FXHOOD horizontal vent terminator instruction sheet (provided with the FXHOOD) prior to installation.

In earthquake-prone zones, CEC recommends that installers use a large washer and lag screw through the existing holes used to hang the heater to affix the upper third of the heater to the mounting board. To affix the lower third of the heater, CEC recommends that two new holes be drilled in the heater’s frame, each one 16 inches below the top two holes, and that washers and lag screws be used to secure the lower portion of the heater to a spacing board.

Expansion and contraction of piping due to changing water temperature in the pipes imparts movement to the heater which, if mounted directly to a brittle, friable board, such as plasterboard, can cause failure of mounting.

The incandescent particle tray (shipped loose in the carton with the water heater) must be attached at the bottom of the water heater front cover at the time of installation. Use the screws provided. See figure 3.

SCREWS

INCANDESCENT PARTICLE TRAY

Fig. 3 - Incandescent Particle Tray Illustration

13 ¼”

WALL STUDS

SUPPORT BOARD

1” X 4”

SPACE BOARD

Fig. 2 - Mounting the Heater

6

6 720 606 601

Image 6
Contents For Your Safety Table of ContentsWhat to do if YOU Smell GAS Features Unpacking the Aquastar HeaterFront View Side View TOP a Front B Back Sides Floor C Vent DiameterProper Location for Installing Your Heater General Rules to Follow For Safe OperationCombustion AIR Requirements ClearancesMounting Installation Incandescent Particle Tray IllustrationVenting Feet 4.6 m with twoHorizontal Side Wall Soffit GAS Connections GAS Line SizingGAS PIPING, Connections GAS Line Sizing For Natural GASFor LP GAS Water valve and water connectors, top view Water ConnectionsFlue gas safety device Electrical ConnectionsFor Your Safety Read Before Operating Your HOT Water Heater Lighting and Operating InstructionsTemperature Adjustment Knob Microswitch adjustment No Spark AT the PilotPilot Sparks Continuously with no Water Running FAN Circulates When HOT Water is Shut OFF Diagram of AquaStar 125FX Interior Components Diagram and Parts List Interior Components Diagram Parts List 125FX Flow chart of Aquastar 125 FX Limited Warranty Maintenance Table see page15

125FX NG, 125FX LP specifications

The AquaStar 125FX NG and 125FX LP are two remarkable models in the world of high-efficiency heaters. Designed for optimal performance in residential settings, these devices cater to diverse needs with their advanced technology and user-friendly features.

The AquaStar 125FX NG model operates using natural gas, while the 125FX LP utilizes liquid propane. This versatility allows users to choose the most suitable fuel type for their home setup. Both models boast an impressive energy efficiency rating, ensuring minimal energy waste while delivering reliable hot water on demand. This makes them not only cost-effective but also an eco-friendly choice for homeowners looking to reduce their carbon footprint.

One of the standout features of the AquaStar 125FX series is its compact design, which makes it ideal for installations in small spaces. With a sleek and modern appearance, it can easily blend into various interior aesthetics without occupying excessive room. The units are also relatively lightweight, facilitating a simple installation process.

In terms of performance, both the NG and LP models are equipped with a powerful BTU input that guarantees quick heating capabilities. They can provide ample hot water for multiple applications simultaneously, such as showers and dishwashing, making them perfect for busy households. Furthermore, the AquaStar 125FX units utilize advanced burner technology that ensures efficient combustion, resulting in a constant supply of hot water without fluctuations in temperature.

Safety is paramount in the design of the AquaStar 125FX series. Each heater is equipped with comprehensive safety features, including built-in vents for proper exhaust and a flame failure device that shuts the heater off if the flame goes out unexpectedly.

The control panel on both models is intuitive, allowing users to easily adjust the water temperature and monitor the unit's performance. Additionally, the AquaStar 125FX series is designed for longevity, with corrosion-resistant materials that withstand the rigors of daily use.

In summary, the AquaStar 125FX NG and 125FX LP are perfect examples of modern, efficient water heating technology. With their compact design, rapid heating capabilities, and robust safety features, these models present an excellent choice for any home looking to enhance its hot water supply while maintaining efficiency and environmental responsibility.