Bradford-White Corp DS150S, DS140S instruction manual VENT-AIR Intake System Installation

Page 17

Installation continued-

VENT-AIR INTAKE SYSTEM INSTALLATION

WARNING

The vent-air intake system must be properly installed. Failure to properly install the vent-air intake system could result in property damage, personal injury or death.

Do not install any damaged vent-air intake system components. Contact the manufacturer of the water heater for replacement parts.

IMPORTANT

When the following instructions specify, to seal a vent-air intake joint, use only Loctite Ultra Blue 587 RTV Silicone sealant. A tube of Loctite Ultra Blue 587 RTV Silicone sealant is supplied with every direct vent water heater and each optional vent-air intake kit. Make sure that all joints are completely sealed.

When drilling pilot holes for the #8 sheet metal screws through the five (5) inch (12.7 cm) diameter components, be careful not to drill into the inner three (3) inch (7.6 cm) diameter components.

Tools Required For Vent-Air Intake Installation

The following minimum tools are required to properly install the vent- air intake system. Note: Wall construction will determine tool usage.

Tape Measure Drill

3/16 inch Diameter Drill Bit(s) 1/8 inch Diameter Drill Bit(s)

Masonry Drill Bit(s) (For Poured Concrete, Concrete Block and Brick Wall Construction)

Reciprocating Saw w/appropriate Blade(s) (Dependent on Wall Construction)

Chisel (For Poured Concrete, Concrete Block and Brick Wall Construction) Hammer (For Poured Concrete, Concrete Block and Brick Wall Construction)

1/4 & 5/16 inch Nut Drivers (Preferred) or Slotted Head Screwdriver

Phillips Head Screwdriver

17

Image 17
Contents What to do if YOU Smell GAS Direct Vent GAS Water HeaterCongratulations Table of Contents General Information General Information Locating the Water Heater InstallationDo not Operate Appliance Until the Leakage is Corrected If YOU Smell GASInstallation Locating The Water Heater Optional Direct VENT-AIR Intake Terminal Guard Minimum ClearancesInstallation Minimum Clearances Installation Venting Exceptions for Installations in CanadaInstallation Venting Horizontal and Vertical VENT-AIR Intake Lengths Table a Installation Horizontal and Vertical Vent-Air Intake Lengths Tools Required For Vent-Air Intake Installation VENT-AIR Intake System InstallationInstallation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Water Connections Page First Being Certain IT is Filled with Water Installation Water Connections GAS Connections To Fill the Water Heater General OperationPage Thermostat Adjustment Burner Flame Checks Burner Flame Checks MaintenanceMaintenance Part Name & Description This Manual should be Kept with the Water Heater Direct Vent Water Heater VENT-AIR Intake Kits

DS150S, DS140S specifications

Bradford White Corp is renowned for its commitment to quality and innovation in the water heating industry, and its DS140S and DS150S models exemplify this dedication. Designed for residential and light commercial applications, these models bring efficiency, performance, and advanced technology to the forefront of water heating solutions.

The DS140S and DS150S are both powered by high-efficiency gas burners that deliver rapid heating capabilities. With input ratings of 140,000 BTU/hr and 150,000 BTU/hr respectively, these water heaters are ideal for homes and businesses that require a substantial volume of hot water quickly.

One of the standout features of these models is Bradford White's patented Hydrojet Total Performance System. This system optimizes the heating process by creating a more efficient flow of water within the tank, reducing sediment buildup over time. This results in improved energy efficiency and longer tank life, as well as maintaining the quality of the water being heated.

In addition, both models are equipped with Bradford White's Vitraglas® interior coating, which provides exceptional protection against corrosion. The Vitraglas coating is not only durable but also enhances the longevity of the tank, ensuring reliable performance for years to come.

Another notable characteristic of the DS140S and DS150S is their advanced electronic gas control system. This feature allows for precise temperature regulation, ensuring that the water remains at the desired temperature while reducing energy consumption. The intuitive interface simplifies operation, making it accessible for users of all skill levels.

Safety is paramount, and Bradford White incorporates various protective measures within these models. The flame arrestor design enhances the safety profile by preventing flashback, while the temperature and pressure relief valve ensures that the tank operates within safe limits.

Furthermore, the DS140S and DS150S models are designed with ease of installation and maintenance in mind. Compact designs and versatile venting options allow these water heaters to fit into tight spaces, making them suitable for various installation environments.

In summary, Bradford White Corp’s DS140S and DS150S models combine innovative technology, efficiency, and safety features, making them excellent choices for anyone in need of a reliable water heating solution. With robust construction, high-performance capabilities, and advanced features, they are sure to meet the demands of both residential and light commercial applications.