Bradford-White Corp DS140S, DS150S instruction manual Installation, Locating the Water Heater

Page 6

INSTALLATION

LOCATING THE WATER HEATER

WARNING

Water heaters are heat producing appliances. To avoid damage or injury, do not store materials against the water heater or vent-air intake system. Use proper care to avoid unnecessary contact (especially by children) with the water heater and vent-air intake components. UNDER NO CIRCUMSTANCES

MUST FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.

DO NOT install the water heater in any location where gasoline or flammable vapors are likely to be present.

Water Heaters in residential garages shall be installed so that all burner(s) and burner ignition device(s) are located not less than 18 inches (46 cm) above the floor and shall be located, or protected, to avoid physical damage. For other installations refer to local codes. In the absence of local codes, the water heater shall be installed in compliance with the National Fuel Gas Code, ANSI Z223.1 - (Latest Edition) and/or in Canada, CA /CGA B149 Installation Codes (Latest Editions).

The location of this water heater is of the utmost importance. Before installing this water heater, read the installation section of these instructions. After reading these installation and operating instructions, select a location for the water heater where the floor is level and is easily accessible to gas and water supply lines. DO NOT locate the water heater where water lines could be subjected to freezing temperatures. Make sure the cold water pipes are not located directly above the gas control so that condensate during humid weather does not drip on the controls.

6

Image 6
Contents Direct Vent GAS Water Heater What to do if YOU Smell GASCongratulations Table of Contents General Information General Information Installation Locating the Water HeaterIf YOU Smell GAS Do not Operate Appliance Until the Leakage is CorrectedInstallation Locating The Water Heater Minimum Clearances Optional Direct VENT-AIR Intake Terminal GuardInstallation Minimum Clearances Installation Exceptions for Installations in Canada VentingInstallation Venting Horizontal and Vertical VENT-AIR Intake Lengths Table a Installation Horizontal and Vertical Vent-Air Intake Lengths VENT-AIR Intake System Installation Tools Required For Vent-Air Intake InstallationInstallation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Installation Vent-Air Intake System Installation Water Connections Page First Being Certain IT is Filled with Water Installation Water Connections GAS Connections General Operation To Fill the Water HeaterPage Thermostat Adjustment Burner Flame Checks Maintenance Burner Flame ChecksMaintenance Part Name & Description This Manual should be Kept with the Water Heater Direct Vent Water Heater VENT-AIR Intake Kits

DS150S, DS140S specifications

Bradford White Corp is renowned for its commitment to quality and innovation in the water heating industry, and its DS140S and DS150S models exemplify this dedication. Designed for residential and light commercial applications, these models bring efficiency, performance, and advanced technology to the forefront of water heating solutions.

The DS140S and DS150S are both powered by high-efficiency gas burners that deliver rapid heating capabilities. With input ratings of 140,000 BTU/hr and 150,000 BTU/hr respectively, these water heaters are ideal for homes and businesses that require a substantial volume of hot water quickly.

One of the standout features of these models is Bradford White's patented Hydrojet Total Performance System. This system optimizes the heating process by creating a more efficient flow of water within the tank, reducing sediment buildup over time. This results in improved energy efficiency and longer tank life, as well as maintaining the quality of the water being heated.

In addition, both models are equipped with Bradford White's Vitraglas® interior coating, which provides exceptional protection against corrosion. The Vitraglas coating is not only durable but also enhances the longevity of the tank, ensuring reliable performance for years to come.

Another notable characteristic of the DS140S and DS150S is their advanced electronic gas control system. This feature allows for precise temperature regulation, ensuring that the water remains at the desired temperature while reducing energy consumption. The intuitive interface simplifies operation, making it accessible for users of all skill levels.

Safety is paramount, and Bradford White incorporates various protective measures within these models. The flame arrestor design enhances the safety profile by preventing flashback, while the temperature and pressure relief valve ensures that the tank operates within safe limits.

Furthermore, the DS140S and DS150S models are designed with ease of installation and maintenance in mind. Compact designs and versatile venting options allow these water heaters to fit into tight spaces, making them suitable for various installation environments.

In summary, Bradford White Corp’s DS140S and DS150S models combine innovative technology, efficiency, and safety features, making them excellent choices for anyone in need of a reliable water heating solution. With robust construction, high-performance capabilities, and advanced features, they are sure to meet the demands of both residential and light commercial applications.