A.O. Smith GPDT, GPDX, GPDH owner manual Optional Field Installed Wiring

Page 11

GROUNDED IN ACCORDANCE WITH LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70.

If local codes do not permit use of a flexible power supply cord.

OPTIONAL Field Installed Wiring

1.Remove screws to remove wiring junction cover.

2.A standard 1/2" conduit opening has been made in the water heater junction box for the conduit connection.

3.Use wire nuts and connect the power supply wiring to the wires inside the water heater's junction box.

4.Be certain that neutral and line connections are not reversed when making these connections.

5.Replace front plate and secure with screws.

WARNING

DISCONNECT FROM ELECTRICAL SUPPLY BEFORE SERVICING UNIT. REPLACE ALL DOORS AND PANELS BEFORE OPERATING HEATER.

IF ANY OF THE ORIGINAL WIRES SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH APPLIANCE WIRE MATERIAL WITH MINIMUM TEMPERATURE RATING OF 105°C AND A MINIMUM SIZE OF NO. 18 AWG.

FIGURE 24.

SCHEMATIC DIAGRAMS

FIGURE 26.

T & P VALVE AND PIPE INSULATION

(ON SELECTED MODELS)

Remove insulation for T & P valve and pipe connections from carton.

Fit pipe insulation over the incoming cold water line and the hot water line. Make sure that the insulation is against the top cover of the heater.

Fit T & P valve insulation over valve. Make sure that the insulation does not interfere with the level of the T & P valve.

Secure a ll insula tion using tape.

FIGURE 25.

FIGURE 27.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Residential GAS Model Replacement Parts and Deliming ProductsWith HOT Surface Ignition Insulation Blankets External DamageChemical Vapor Corrosion Extended NON-USE PeriodsWater Potable Heating Space Heating Location of HeaterWater Connections Venting Closed Water SystemGAS Connections Venting Through an Outside Wall Clearances Combustion AIR and ExhaustVenting Through Roof Clearances Wire FenceVenting Through AN Outside Wall DIA. Vents Number of 90 DEG Venting System Example Installation For ALL ModelsVent piping can be installed as follows Movement Complete Joint SET Approximate Setting Time for 2-1/2 to 4 Pipe JointsVent Pipe Separation Cementing PVC, ABS or Cpvc Pipe and FittingsElbows WiringConnecting Vent to Blower Venting Through a RoofOptional Field Installed Wiring Do not TRY to Light the Burner by Hand What to do if YOU Smell GASFilling Temperature RegulationControl Sequence HOT Surface Direct Ignition High Altitude InstallationVenting Manual Reset Switch Water Heating Ignition SequenceVenting System High Temperature Limit SwitchPower Venter Maintenance Main BurnerThermostat and GAS Supply Check Service and RepairWater Heater Control LED Status Problem Solution Trouble ShootingCondensation HOT WaterVent Pipe TOO HOT Yellow FlameLimited Residential GAS Warranty Southeast Parkway FRANKLIN, TN

GPDT, GPDH, GPDX specifications

A.O. Smith is a renowned leader in the manufacturing of water heating solutions, and its series of gas water heaters, including the GPDT, GPDH, and GPDX models, are emblematic of the company’s commitment to innovation, efficiency, and reliability.

The A.O. Smith GPDT series is characterized by its high energy efficiency and robust design. With a 40-gallon capacity, it utilizes a 0.67 energy factor, making it an ideal choice for both residential and light commercial applications. This model features a unique combustion system that minimizes emissions while maximizing hot water output. Equipped with a powered draft system, the GPDT series effectively vents combustion gases, improving air quality and lowering operational costs.

In contrast, the GPDH series is particularly notable for its compatibility with high-efficiency gas appliances. It employs a direct vent system, allowing for versatile installation options. The GPDH models also include advanced diagnostics and a LED display that simplifies monitoring and maintenance. With an enhanced insulation design, these heaters minimize heat loss, effectively optimizing performance and energy savings.

The GPDX series capitalizes on cutting-edge technologies to provide superior performance. With capacities ranging from 30 to 50 gallons, these water heaters are designed to meet varying needs. The GPDX is equipped with a dual-purpose valve that offers superior temperature control and safety features, ensuring user convenience and peace of mind. Its intuitive interface allows users to easily set their desired water temperature and monitor performance metrics.

One of the key characteristics that unify the GPDT, GPDH, and GPDX models is their commitment to durability. A.O. Smith incorporates high-quality materials and innovative engineering processes to enhance the longevity of their products. Each model features an impressive warranty, demonstrating the company’s confidence in their craftsmanship.

In conclusion, A.O. Smith's GPDT, GPDH, and GPDX gas water heater series offer a blend of efficiency, performance, and innovation. These models are equipped with advanced technologies designed to provide users with reliable hot water solutions while minimizing energy consumption. With their robust build, user-friendly features, and impressive warranties, A.O. Smith continues to be a top choice for those seeking dependable gas water heating solutions.
Top Page Image Contents