Harman-Kardon Installation & Configuration, If the PT2500’s front panel remote sensor

Page 9

•PT2500(g).qx 10/23/96 7:36 AM Page 8

Installation & Configuration

7

Your new Harman Kardon receiver is designed to provide the best reproduction from both movies and musical programs. To assure that the unit operates to its fullest capability, it is important that you spend a few minutes to properly install and configure all of the elements in your new system. Some, or all of the following steps will apply to your system, depend- ing on the equipment in use. If you have any questions concerning the installation of this product consult your local dealer, or contact the Harman Kardon web site at http://www.harmankardon.com.

System Component

Connections

IMPORTANT SAFETY NOTE: Many products feature automatic turn on cir- cuitry which may accidentally be activat- ed when making connections. For your safety and to prevent damage to speakers, amplifiers and other components we strongly recommend that all equipment power be turned off, or that AC power cords be unplugged when any system connections are made or changed.

Using high quality interconnect cables, connect all source components to the appropriate input jacks on the rear panel. When connecting audio recorders and VCRs it is important to make certain that the PLAY/OUT jacks on the recorders are connected to the PLAY jacks on the PT2500, and that the RECORD/IN jacks of the recorders are connected to the REC jacks on the PT2500.

If the phono input is used, connect the small ground wire connection furnished on most turntables to the System Ground Terminal ªon the rear panel. This will greatly reduce system noise and hum.

Assemble the supplied AM loop antenna as shown below and connect it to the AM ANTENNA Terminals e.

AM LOOP ANTENNA SETTING

LEG

Stand and place it on a shelf, or hang it on a wall.

It may be necessary to rotate the antenna or change its position to achieve the best AM reception. Connect an FM antenna to the FM Antenna Terminals. A 300 ohm to 75 ohm adapter may be required for some antennae.

If a PA5800 or other compatible amplifi- er will be used, connect the supplied accessory cable to the Remote Amplifier Trigger Jack Ýon the PT2500. Connect the other end to the appropriate jack on your amplifier. Consult the amplifier manual for further instructions.

IMPORTANT NOTE: Do not connect amplifier trigger cables to the “IR Remote Control” jacks on this or any other equipment.

If you are using the PT2500 to switch video inputs, connect either MONITOR output Üto a video input on your TV or projector.

The rear panel accessory outlets on the PT2500 may be used to power low cur- rent devices such as CD payers or tape decks. The SWITCHED Accessory AC Power Outlets àare activated only when the PT2500 is turned on. The

UNSWITCHED Accessory AC

Power Outlets ßmay be used with VCRs, as the power to these outlets is live as long as the PT2500 remains connect- ed to an AC power source.

CAUTION: The total power load for all products connected to the accessory out- lets must not exceed 100 watts. Do not use them for high current devices such as power amplifiers.

If the PT2500’s front panel remote sensor

ñis blocked by cabinet doors you may still operate the unit via remote control with the use of an optional external remote sensor. Connect the output of the sensor to the rear panel REMOTE

CONTROL Extension Input á. This jack may also be used as the IR input from compatible multiroom con- trol systems. The sensor may be looped to other components by connecting the

REMOTE CONTROL Extension

Output ¡to the IR remote input jack of other compatible components.

Amplifier Connections

Since the PT2500 is a tuner/preamplifier, it does not include any on board power amplifiers. The final step in the installa- tion process is to connect the unit to the amplifiers for each channel. Using high quality audio interconnect cables, con- nect the FRONT, CENTER and

SURROUND Channel Outputs

cbato the appropriate input jacks of a power amplifier.

PT2500 rev (G) 10/23/96

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Harman Kardon PT2500 VSurround Tuner Controller Table of Contents Features Introduction and Safety InformationSystem remote control Remote Trigger Control for PA5800 Verify Line Voltage Before UseCleaning Installation LocationDo Not Open The Cabinet Catv or Antenna GroundingNumber within a square references a front panel control Unpacking and InstallationFront Panel Controls Rear Panel Connections Power Button Press this button to turn the PT2500 on or off System Remote ControlInstallation & Configuration Cbato the appropriate input jacks of a power amplifierIf the PT2500’s front panel remote sensor When using the PT2500 with an external Delay Setting Output Level CalibrationTo calibrate your system, follow these steps Center Channel Mode Operation Surround Mode OptionsAuto Tuning Manual TuningPreset Tuning Recalling Preset StationsIf the problem is Make sure that TroubleshootingPreamplifier Section SpecificationsTuner Section FM Tuner Section AM

PT2500 specifications

The Harman-Kardon PT2500 is a noteworthy addition to the realm of audio equipment, known for its blend of performance, design, and innovative technologies. Aimed at audiophiles and casual listeners alike, this audio system exemplifies the brand's commitment to delivering high-quality sound experiences.

One of the standout features of the PT2500 is its advanced amplification technology. With a powerful output, it ensures that audio is delivered with clarity and precision, whether you’re listening to soft melodies or booming bass lines. The integrated amplifier is designed to optimize audio performance and can handle a wide range of speakers, allowing users to create a bespoke sound system tailored to their needs.

The PT2500 employs Harman-Kardon's proprietary technologies, including their signature surround sound processing. This feature allows users to enjoy an immersive audio experience, making movies, music, and games come alive with rich soundscapes. The system is equipped with multiple audio decoding capabilities, such as Dolby Digital and DTS, ensuring compatibility with various formats and content types.

In terms of connectivity, the PT2500 offers versatile options, catering to modern digital demands. With multiple inputs including HDMI, optical, and analog connections, users can connect various devices such as televisions, gaming consoles, and streaming players. Additionally, Bluetooth capability enables wireless streaming from smartphones and tablets, enhancing convenience and flexibility.

The design of the Harman-Kardon PT2500 is both aesthetic and functional. Its sleek, modern look is complemented by intuitive controls, allowing users to navigate settings effortlessly. The build quality reflects Harman-Kardon's commitment to craftsmanship and longevity, ensuring that the product not only looks good but also stands the test of time.

Another key characteristic is the customizable audio settings, which allow users to tailor their listening experience to their preferences. Whether it's adjusting bass levels or fine-tuning treble, the PT2500 accommodates individual tastes and room acoustics, ensuring optimal sound delivery.

In conclusion, the Harman-Kardon PT2500 stands out as a remarkable audio system that combines performance, versatility, and style. With its array of features and technologies, it caters to the diverse needs of today’s audio enthusiasts, making it an excellent choice for those seeking to elevate their listening experience. Whether at home or in a dedicated media room, the PT2500 promises to deliver high-quality sound that resonates with every listener.
Top Page Image Contents