Insert Screw

If your original transmitter has two or three buttons and uses DIP switches, set the #1 LED in the GDK to the opposite position on the first DIP switch of your original transmitter. Set the remaining GDK LEDs to the exact same position of your original transmitter’s DIP switches. If your original transmitter has two or three buttons but does not have DIP switches inside the original transmitter or if the original transmitter is lost or broken, please use the DIP switches located on the radio receiver (near the head unit) or at the push button located on the garage wall. The radio receiver can be found on or near the garage door opener motor head mounted on your garage ceiling. The DIP switches are usually located near the point where the electrical enter the garage door opener head or on the externally mounted radio receiver. YOU DO NOT NEED TO DISASSEMBLE THE GARAGE DOOR HEAD OR RADIO RECEIVER TO LOCATE THE DIP SWITCHES, HOWEVER, YOU MAY HAVE TO REMOVE THE PROTECTIVE COVER.

The GDK should be mounted to an outside wall, close to your Garage Door. Mount the GDK on a flat vertical surface with enough room above the GDK to slide the cover up. The location should be easily reached by anyone who will use it, at least five feet above the floor and clear of any moving Garage Door parts. It is recommended that you choose a location that is not in direct sunlight. If you mount the GDK in a location that is exposed to direct sunlight, the LEDs will be difficult to see. It is also recommended that you do not mount the GDK onto a metal surface, as this may reduce the range of the signal. To mount the GDK:

1.Using one of the supplied 1” screws, drive the screw into the wall in your chosen location, leaving 1/4” of the screw protruding from the wall.

2.Slide the GDK onto the screw, see figure 6.

Figure 6

3.Remove the battery cover and disconnect the battery. This will not erase the passwords or security codes already stored in the GDK’s memory.

4.Drive the second 1” screw through the hole at the rear of the battery compartment.

3.Remove the battery cover and disconnect the battery. This will not erase the passwords or security codes already stored in the GDK’s memory.

4.Drive the second 1" screw through the hole at the rear of the battery compartment.

Figure 7

NOTE: Make sure that the GDK is aligned in an upright position before driving in the second screw.

5.Re-attach the battery and slide battery cover back into place.

After you have stored your garage door opener(s) security codes in the memory the GDK and you have mounted the unit you are ready to use your GDK. To open your garage door:

1. P I N Open the GDK’s cover or, if the w cover is already open, press

ENTER. Key in your PIN, then press ENTER. The GDK will beep.

NOTE: If you enter an incorrect PIN the times, the GDK will lock you out for on. minute. After one minute, re-enter the correct PIN to proceed with opening you garage door.

Press DOOR1, DOOR2 or DOOR3, depending on which door you would like to open. The GDK will send a signal to your garage door opener for as long as the DOOR1 , DOOR2 or DOOR3 key

is pressed. Once you release one of the keys, the signal will stop. Your garage door will open. Thirty seconds after the last key press, the GDK will power off.

NOTE: After selecting the door to be operated by pressing DOOR1 , DOOR2 or DOOR3, pressing any key other than EXIT will open or close that specific garage door.

If, after opening DOOR1, you would then like to open DOOR2 or DOOR3, press the EXIT key once and then press DOOR2 or DOOR3 to open another door.

A Do NOT allow children to play with the transmitter or door opener, If children must use the GDK, please supply proper training first.

Keep people clear of the garage

Adoor as it is opening and closing. The garage door could cause serious injury or death.

Use the GDK only when you are

Asure that all possible obstructions have been removed.

Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com

AR90, AR85, SD9500 specifications

The Genie SD9500, AR85, and AR90 are three advanced machines designed for specific applications in various industries, including construction, maintenance, and warehousing. Each of these models showcases the commitment of Genie to innovation, quality, and safety, catering to the diverse needs of their operators.

The Genie SD9500 is a robust scissor lift that is designed for heavy-duty performance. One of its standout features is its impressive lifting capacity which allows it to safely raise significant loads to heights of up to 32 feet. The SD9500 is equipped with a durable hydraulic system that ensures smooth and efficient operation. Its expanded platform size enhances work area accessibility, making it a favorite in large maintenance tasks. The machine’s all-terrain capabilities, reinforced with rugged tires and a stable base, allow it to navigate various surfaces, ensuring optimal performance in challenging environments. Additionally, the model incorporates advanced safety features such as guardrails and an emergency descent system, emphasizing Genie’s focus on user safety.

Moving on to the Genie AR85, this articulated boom lift exemplifies versatility and maneuverability. It can reach working heights of up to 85 feet with exceptional horizontal outreach, making it ideal for tasks that require precision at height. One of its key technologies is the articulated arm, which enables operators to easily navigate around obstacles and access hard-to-reach areas. The AR85 is powered by an efficient electric motor, making it environmentally friendly for indoor use while maintaining high performance. The lift's compact design allows it to fit through standard doorways, enhancing its usability in tight spaces. Moreover, the AR85 is equipped with advanced control systems that provide intuitive operations, allowing for easy maneuvering.

The Genie AR90 takes versatility a step further with its enhanced capabilities. It boasts an extended reach, with working heights exceeding 90 feet, and offers a wider array of articulation for even better access. This model is equipped with a dual-fuel engine, facilitating operation in both electric and gas modes, providing flexibility depending on job site requirements. The AR90 also features advanced stabilization technology, ensuring secure operation on uneven terrain. Its spacious platform can accommodate more personnel and equipment, making it ideal for larger projects where productivity is essential.

In summary, the Genie SD9500, AR85, and AR90 are powerful machines that incorporate modern features and technologies to enhance lifting operations across various sectors. With their focus on safety, performance, and adaptability, these models showcase the innovative spirit of Genie and their commitment to meeting the needs of operators while ensuring maximum efficiency and safety on the job.