Genie AR85, SD9500, AR90 user manual Stanley Automatic Doorman Vemco

1.Slide open the cover. The GDK’s keypad will illuminate.

2.Press the number 9 eight times, then

mx8 press ENTER, the GDK will beep oo*I

once and the green LED will w illuminate for two seconds followed

by two quick beeps. The GDK will power OFF. This clears the GDK of any previous passwords and security codes so that you can begin a new setup. Your GDK has now ready to learn your new password and garage door security code(s).

NOTE: Use the reset code only to clear the GDK of all passwords and garage door security codes.

1.Select a PIN (Personal Identifica- tion Number) and write it down. This will be your password. Your PIN can be up to 8 digits long.

Press the ENTER key to illuminate & the GDK’s keypad.

5.PIN Enter the PIN you wrote down in B STEP 1 then press ENTER. The

GDK will emit a double-ticking sound to prompt you to confirm your new password. Now reenter the PIN and

PIN press ENTER again. If you entered w the same PIN correctly, the green

LED will illuminate for three seconds followed by two beeps. The GDK will then power OFF.

NOTE: If you make a mistake in entering your PIN, press the EXIT key and return to STEP 2 to re-enter your new PIN.

You will need your original garage door opener when setting up GDK’s garage door security code. Open your original garage door opener so that you can view the DIP switches.

1 .PlN Open the GDK’s cover or, if the w cover is already open, press

ENTER. Key in your PIN followed by ENTER. The GDK will beep and the green light will blink twice if the PIN is correctly entered. If you enter your PIN incorrectly, the GDK will beep and the red light will blink once.

I

3

4

5

6

MULTI-CODE AMBASSADOR MULTI EL MAC

MOORE-O-MATIC LINEAR DELTA SHIMA POWERLIFT

GENIE MODEL AT90

GENIE MODEL SD9500

LIFTADOOR

BLUE MAX EZ LIFT

GENIE MODEL AR85

CHAMBERLAIN SEARS RAYNOR LIFT-MASTER WAYNE DALTON MASTER MECHANIC

STANLEY

AUTOMATIC

DOORMAN

VEMCO

10 BITS/300 MHZ

8 BITS/310 MHZ

12 BITS/390 MHZ

9 BITS/390 MHZ

9 BITS/390 MHZ TERTIARY BITS

10 BITS/31 0 MHZ

3.w Press tne number 1 (Factory

’Default Password) followed by vENTER. The green LED will blink

two times followed by one beep. The GDK is now on and ready to learn your new password (PIN).

Press STORE followed by the PlN1, PIN2* or PIN3* key. The first red LED, corresponding to PIN1, will light and remain lit as the green LED blinks.

*NOTE: The first time you enter a password, GDK automatically defaults that password to PIN1, even if PIN2 or PIN3 is pressed.

Press STORE followed by DOOR1, DOOR2 or DOOR3. The first six LEDs will chase. Enter the number (1-6) from the table for your brand of garage door opener (See Figure 4). The corresponding LED will light.

NOTE: If you make a mistake during the set up process, press the EXIT key, re-enter your PIN and return to step 1 in the "SETTlNG UP THE SECURITY CODE TO OPERATE YOUR GARAGE DOOR" section to re-enter your garage door opener’s code.

3.Press ENTER. All of the LEDs will w begin to chase, then the first LED

will blink.

Using the UP, MID and DOWN keys, match the LEDs to the DIP switches in your original garage door opener. When you press UP, the LED will remain on. When you press MID, the LED will flash slowly and when you press DOWN, the LED will remain off.

NOTE: The LED s must match exactly to the DIP switches on your original garage door opener.

Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com